flash drive case 3d models

Jetson nano case

The white indicator light on the controller board isn't really needed for an optical drive, and I considered either cutting it off or providing a place where I could just leave it clipped inside the case. But, in the end, I mounted it so that it was...

The case is specifically tailored to fit the Seagate drive's dimensions - approximately 120 mm in length, 82 mm in width and just 18 millimeters high. A touch of extra padding was added to ensure a snug fit, so these measurements may not be exact. ...If...

This is a mockup for case design.

This is a mockup for case design.

This is a compact enclosure designed specifically for a 2.5-inch laptop solid-state drive.

7 parts. ...Easy to print. Some glue needed. Some sanding required. Three SSD drives fit inside.

This is a straightforward process of creating an external CD/DVD from an outdated internal 5.25-inch drive.

In the previous episode...Using the innards of my redundant Hitachi Simpledrive USB HDD, I previously created a TPU case to hold the PCB and the optical drive from my old PC - thing 6172462.But it all went horribly wrong (dah dah DAHHH!). The idea...

Here are some general instructions: http://www.cpcwiki.eu/index.php/Guide_on_how_to_connect_a_3.5"_drive_to_a_CPC6128/664 And here's a French translation: http://www.amstradtoday.com/upgrade/upgrade.htm You'll need the following for this project: 1...

This innovative design holds the hard drive in place solely with friction, ensuring a snug fit that's crucial to its stability. For added security, you can incorporate pieces of paper to reinforce the enclosure's grip on the drive. **Updates:** *...

I constructed a modified version of a previously discovered scenario in order to allow for better airflow and prevent my hard drive from overheating.

... a 2.5" hard drive without need for screws. ... It is designed to hold the hard drive only with friction, so the accuracy is relatively important (or you can add pieces of paper to make it secure). ... -Added .step file -Added pictures of the adapter

... the need for screw installation. ...This device holds the hard drive securely in place using friction alone, making precision a key factor in its functionality. ...To enhance stability, users can also insert small pieces of paper to reinforce the hold.

Remix of 2.5 inch hdd case that'll also fit an SATA USB connector.

I swap out my trusty Seagate Expansion Portable Drive for a fresh one. ...After disassembling it, I noticed all the plastic clips were badly damaged so I opt to build a new enclosure from scratch.

In this remix I adjusted the height of the parts to allow fitting an Amiga 500 Chinon FB-354 disk drive. ... a fitting faceplace can be found in this other remix: https://www.thingiverse.com/thing:6062923

My case has mounts like an Antec case, but it isn't actually Antec and the source model was too thick, so I halved it in PrusaSlicer and mirrored it.

SSD External Case for USB use. ... Uses the StarTech.com Cable USB3S2SAT3CB Using a Samsung SSD 850 EVO 500Gb

... for a 3V. Use some hotglue for the relays in the base. You don't have to fasten Sonoff Pow, that clamps through the lid. If you have no knowledge of electronics, let this one pass you by. case monitor pow power relais relay sonoff Tasmota

Made a case for my OctoPi implementation. ... Not much on ventilation, but the pi stays under 63c at full load with ambient temp of 21c (70F).

Made a case for my OctoPi implementation. ...Not much on ventilation, but the pi stays under 63c at full load with ambient temp of 21c (70F).</p>

an adapter for this part: https://cults3d.com/en/3d-model/gadget/2x-hdd-caddy, or the maker's 1x version, for my modular case system.

Edit it online https://www.tinkercad.com/things/aXf244JNCVI This is mixed to difrent thing for direct drive.I couldnt find orginal post ID so orginal files url was below. ... https://www.thingiverse.com/thing:4566739 ...

A simple TPU case was designed with holes for the USB cable, indicator lights, and additional openings to reduce weight. The sidewalls of the open holes provide rigidity and prevent soft spots. Printing two cases in blue and red would creates a...

I designed a custom casing for my small USB to USB mini 32 GB stick, which works perfectly with both my smartphone and computer. The original case had cracked, so I took the initiative to create a new one that would fit this specific size of USB...

Just a small adapter to let this part: https://cults3d.com/en/3d-model/gadget/2x-hdd-caddy (or the maker's 1x version) attach to my modular case system. ...The screw holes are 3.5mm in the adapter

Just a simple holder for 8 normal sized SD-cards and 4 flash drives

If someone need something more specific and don´t have the time/skils to make nesessary change, I´ll be happy to help.Notes:The case from the pictures it from earlier version, and I have expirienced some filament flow problems. ...Currently I dont have...

... adapter. The opening on this enclosure will fit most adapters available, but the Fusion360 file is also included just in case. ...If you need something custom and don't have time or skills to make the necessary adjustments, I'm happy to assist you.