fit rx pro 3d models

Left to our own devices to scour the net for solutions, (clearly we weren't the first people with CR10S Pro V2's to have purchased this product...right?!?) well after printing three different models that just didn't fit my setup quite right, I got...

Left to our own devices to scour the net for solutions, (clearly we weren't the first people with CR10S Pro V2's to have purchased this product...right?!?) well after printing three different models that just didn't fit my setup quite right, I got...

If they don't fit snugly after printing, wrap a single layer of clear scotch tape around each leg and you should be fine.Available in three designs:PlainEmbossed PacmanEmbossed Ender 3Enjoy! Print SettingsPrinter...

I made it taller so it would allow the filament to feed better on the CR-10 pro v2.

V2 NOW RELEASEDNote: This will NOT fit the Ender model hot end at all.Only CR10S Pro model from MicroSwiss. (https://store.micro-swiss.com/collections/all-metal-hotend-kits/products/all-metal-hotend-kit-for-cr-10-pro)This work is a product of...

I redesigned the original frame for my Ender 3 Pro because it didn't fit correctly. I remixed a new version that works perfectly. To print this, I placed the frame insert on its side with the circular part facing outward and at a 90-degree angle...

It fits perfectly on the new iPhone, but be aware that removing the case can be a bit more challenging than usual. Don't worry if you encounter any difficulties; this is a normal part of using this design. I've made sure the camera lens is...

I found that my Ender 3 pro has press fit pulleys on the X and Y axis stepper motors. I didn't want to damage them by trying to remove them and I wanted a better way to fit dampers on. I created this print so that I could use all the parts already...

I use it myself (the puzzle version) and am really glad to share this with you. It fits perfectly on the new iPhone. It is a bit harder to remove the case though, don't be surprised. This way the iPhone won't get out of it, even if it falls down on...

I wanted a simple snap on filament guide for my Ender 3 S1 pro. ... Remixed this from: https://www.thingiverse.com/thing:4428057 https://www.thingiverse.com/thing:5419960 Needs support for the hole

This remix is an exact match for the Gearbest Arduino Pro Mini board, which comes in slightly smaller dimensions. https://gearbest.com/arduino-scm-supplies/pp_437601.html?wid=21 In addition, the bore size has been reduced to 3.2mm. ... The originator...

Although I've since moved on to a direct drive setup with the CR-10S Pro Direct Drive Bracket With Sensor Mount, which can be found on Thingiverse under ID 3807893, this design still has its uses. ... For those interested in trying out the original...

and adapt the both end to the iPad Pro 12.9 who is a little bit thiner than older iPad, it now can pinch a 5mm tablet firmly, with the tow OEM pad, just secure the upper part with a elastic to be sure the iPad don't take off .... ^^its better i...

Since my original Creality end caps didn't stick anymore after being removed twice, I needed new, tightly fitting caps for my printer. These did the job perfectly. If they don't fit snugly after printing, wrapping a single layer of clear Scotch tape...

everything is snug, external covers don't interfere with ports inside the radio and are made taller; nut cover is press fit, doesn't block the access to sd card; internal adapter, removed some geometry that was unnecessary, hole diameter smaller so...

This is Version 2 of the Friction Fit SG90 Servo Mount - Download Only .stl File Needed. The servo should easily slide right in and possibly snap into place, depending on your printer settings. ... I've included a .step file for adjusting screw-hole...

one side was to thin causing it not to stick together and push fit was to thick so sliced edges and thickened wire channel top part and sliced clamp and added screw in point on clamp and 2nd clap for other end of channel / print 0.8 nozzle with brim...

This a remix from the original design, as the former does not fit at all in my printer profiles. Adjusted around -0.5mm on the profile clamps. For those who might want to adjust even further, I leave here the Fusion 360 solid file. "Replacement...

This a remix from the original design, as the former does not fit at all in my printer profiles. Adjusted around -0.5mm on the profile clamps. For those who might want to adjust even further, I leave here the Fusion 360 solid file. ...

This is a straightforward test print designed to verify the snug fit of one part within another, given a specified tolerance (defaulting at 0.1mm). It also serves as a means to fine-tune flow rate and output size, resulting in a calibration print...

This is a simple tiny test print to see if you can get one part to fit inside the other given the given tolerance (default at 0.1mm). It also helps tune flow rate, output size, etc. The print is almost as instant as you can get for a calibration...

AcroBrat VTX SMA (hex nut pigtail and TBS Unify Pro versions) paired with RX Antenna Mount - a sleek setup sans LED or Buzzer, featuring an XT30 opening. No assistance required; print this design upright. Opt for a 0.3mm layer height and 30% infill...

... same time without impacting sharpening angle.  User may need to measure and vary the opening as stone dimensions vary.  I have also used a heat gun after printing to either slightly open or close the platen walls for a properly snug fit.

Frame holder attachment system specifically designed for mounting Asus Xtion Pro Live RGB-D sensor on a Robotis FR05-H1 high-torque, low-weight robotic arm frame.

Same versatile center mount VTX design now compatible with popular TBS Unify Pro antenna connections, offering users a seamless upgrade path to high-performance wireless video transmission capabilities.

Specifically tailored to attach an ASUS Xtion Pro Live RGB-D sensor directly onto a high-performance Robiots FR-07_H1 servo chassis, optimized for dynamic robotics applications and advanced depth perception. This secure mount secures the sensor in...

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

...... You need to replace every 20mm Standoff with a 10mm Standoff and the 2 30mm in the back with 20mm Standoff in order to make it all fit. After that the ESC is mounted where the Arms meet and the FC is mounted where the DJI Air Unit would usually go.

This Smartphone Mount Secures Your Phone Directly Above the TX, at a Perfect 45-Degree Angle and In-Line with the Antenna, Making It Easy to Use Wherever You Are. ...I Chose High-Quality ABS Black Material and Divided It into Three Convenient Parts for...

As mentioned in the title, this technique eliminates UHF issues by using an internal cable route within the frame. Print with an infill rate of approximately 8% for a light yet strong component. ...Note that the image provided is upside down; photos...