fist 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

Again tilt the drawing slightly, noting that you have the right corner vs the model orientation. It can get a little confusing. Save the Sketch 4. The spacer should automatically be tapered to match the corner height because the angled plane adjusts...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

 I'm confident anyone here can just casually rotate the model right-side up in your slicer.This is licensed CC BY-SA 4.0.  Please feel free to republish this.  Feel free to remix this.  Feel free to use it for commercial purposes and make loads of...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports. I...

This is a multimaterial model. I don't have a multi material printer but learned that you can create a multi material print pretty easily without special hardware (as long as the multi material part does not span over to may layers - otherwise it...

Enjoy my Ulvheim Small Merchant House. It came from my Patreon February Release. Thanks to all my supporters and to Markus Kruse / Terrain4Print, creator of the Ulvheim City. This model is supportless as usual. :)</p> <p>Discover my Ulvheim Remixes...

This is resistant to everyday wear and tear, but we got warned that rust stains are not completely removable.So a stainless clothes drying rack became necessary.Most commercial ones just have powder-coated steel tubes which rust after some...

I made a small update to it, adding the model with the included screw threads in the back, and ever since that update the thing is still there but returns a 404 error for everyone who isn't me. I've tried to get it to post, I contacted thingiverse...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

The sourced parts needed are the same than for a MyRCCar OBTS Chassis, so you can use them in all models by now. This means that you can reuse existing parts from other projects, making it easier and more cost-effective to build this chassis. If i...

It is opened by twisting the handles on the doors in a clockwise direction.This was originally uploaded to Thingiverse in 2017, and I have now moved it here as well.I have 14 other Iris boxes designs and I have an instructable describing them and how...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 16 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

UPDATE: 07/16/2019 Project 399 - Front Crossfire Mount - Depressed 3525.stl - I've been running this model the most. I thickened the sides so it provides more lateral stability, improved the chamfer at the sides to make it smoother, and I thickened...

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft: &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;YesSupports: &nbsp; &nbsp;NoI've had the best luck printing these using a single-layer raft, with the part oriented...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

Some model are not there, you can find more here: https://www.cgtrader.com/M600 Instructions I printed mine on a Leapfrog Creatr with ABS (240°) and a bed at 100°. Settings used have been: 0.35mm layer height 2 perimeters 4/4 solid layers...

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

You just have to have the right case respectively.If you use the original MK3S+ frame check out the version for the original Prusa frame.&nbsp;FeaturesWorks with Raspberry Pi 3 and 4Works with any type of Armor-style case that uses M2.5 screws. Just...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

New version available: Please check out the new Ultra Flat Filamentholder model, now updated to be 8mm lower, more accurate, and faster printing :)\nFeatures of the Flat Filament Spool Holder\nJune 6th - Finally finished making it. Enjoy...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on.</p><p>Print the 3 (4) parts. If you...

-Number of facets causes extreme delay in saving/rendering model, likely due to me not understanding the correct scad approach; I am still learning, feel free to leave me any feedback so I can improve my techniques. -Flat ring design (just like the...