firefighter model

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

Models intended to be part of the numbers node all begin with the prefix MMU.Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm.Assembly...

Ok, so i designed another one because the existing models didn't satisfy me. I also made another design myself previously, but i was still not happy. The reason is that i dont know how all the pumps are designed. - Why do some pumps have...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

There were points where I’d get 0.4 and Edwin would be 0.5 with his ruler while using the same model. Chances are that we used a ruler that was slightly wider than what 1mm is in reality.</p><figure class="image image-style-align-center...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

If the format you use is not yet in the downloads, let me know, I will create the models for it. Now print the test part (#0 testmodel) start with the smallest tollerance and try to push the test part over the profile, it should not go strongly...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

 This model is currently a working draft. Solar astronomy has inherent dangers, please be sure you understand these (see also below). Use is at own risk. More general information about this approach to solar astronomy can be found at the Sol'Ex...

Also, I am considering some re-design of the right motor plate that currently interferes with the model fan duct. That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last...

However, the aim was to get this iteration published in the meantime so it will probably be developed as an add-on unit.This future addition will thus enable illumination of the job in hand, be it soldering, 3D printing or anything else requiring...

Please check the images to see what it is included in this kit.This set contains: - Dwarven Berserkers (6 + 6)- Behemot Riders (4 + 4 + 4)- Durnir – Berserker Lord- Tarum Bloodhammer- Thyra Blood Priestess of Duum (Dwarf Pinup)- Skutagaard War...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

Thus I found my way to thingiverse and sought for every model that was irregular eventually finding some customizable builders. While the brick making one is heavy, beam kind was cool, but limited to either halfheight simple or up to # shape with...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The Jedi who wields it is called “F” in the credits.This is a remix of my older model. The biggest changes are:</p><ul><li>Improved mechanism for opening the emitter. It opens up by pressing the blue switch on the side, just as it does on screen. To...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

If you're using the motor in the BOM or Qidi stock motors use this: xplus-imate-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xplus-imate-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print...

Learn everything about the V-Core 3 on the dedicated project page: v-core.ratrig.com. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware)...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

The 3D printing process sometimes leaves whiskers or small blobs of plastic which might jam the fully assembled power train unless each stage is run-in until all parts are worn smooth when the whole will operate as designed.&nbsp; &nbsp;Assembly:1)...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

Real quick: Check out my other S22 designs like my LED handle/boomerangs, help me spread my design by hitting the like button, post a photo as a make once you've printed things out!! There's an active community on this, come:</p><ul><li>join the <a...

The ability to visualize 3D models in real-time enables users to make informed decisions about color palettes, proportions, and overall aesthetic. This level of precision is unmatched by traditional design methods, making Shining 3D Fashion a...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

This model also gives you the possibility to add your own creations and animation them at will. But it’s not all, by printing one more piece and gluing some mirrors to it, you can easily convert the object into a praxinoscope. Furthermore, you have...