fingerboard 3d model

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

The COMPLETE Maneater Nagarots I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Nagarots are a cult devoted to the Serpent Demon Yn'aga, herald of the Tyrant-God...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

I used this here: https://de.banggood.com/Remo-B5509-Ball-Bearings-593mm-For-1621-1625-1631-1635-1651-1655-RC-Vehicle-Models-p-1450586.html - 9x M3 30mm screws and nuts to conetc top and bottom trays - otionally: 9x M3 0.5mm washers to put between...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the...

being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are...

You could also use hex stock cut to the same size, which would increase the weight (since the center of the nuts is hollow) and improve the spin time, but also increases the amount of work that needs to be done in order to build these.The nuts must...

The initial idea was to couple the two 4020s to the original TTBluer case, however it has lower flaps that made the process difficult, as I wanted to preserve the original part without cutting flaps, I decided to model a new case. I have results...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   A Half-Elf who had been sentenced to twelve years of service in The Watchers after maiming her professor. Calanar joined a ranging expedition into the frozen Oldavori wasteland,...

Eye diameter - These three dimensions make up the foundation of this model's unique structure, resulting in eyes that stand out at an impressive six units large. Layer height - Perfect for intricate designs or subtle layering, with a precise setting...

Cap for benq projector lenses, designed for the mx660 model. It fits perfectly. On the outside it has the logo of benq and on the inside that of ho-kago tea time (musical group from the anime k-on). This projector did not have the cover when I took...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_size = 46 stencil_shape = 6 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Some model are not there, you can find more here: https://www.cgtrader.com/M600 Instructions I printed mine on a Leapfrog Creatr with ABS (240°) and a bed at 100°. Settings used have been: 0.35mm layer height 2 perimeters 4/4 solid layers...

Project: Playdough Tool Design Challenge Overview & Background: Through this lesson, students as young as five years old can be introduced to 3-D modeling and desktop fabrication, with an emphasis on its ability to provide solutions to everyday...

Initially I modelled the candle I wanted, then using boolean operations subtracted it from a cube, and split the cube in half. ...Then I added the pins and matching holes just to help align the boxes and hold them together a bit by padding and pocketing...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

This stage can be handled in several ways: 1: The instructor can have several models pre-made for demonstration and discussion. 2: The instructor can have kits of parts put together for students to work with and attempt to build their own trusses. 3:...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...

Not suitable for heated chamber!Below are the temperature results of what I tried************************************************************************************* Notes:The Top_Rods_Cap.stl have a groove preventing 180° rotated insertion (they...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

I know, it's specifically for the Ender 3 & I am using a Mega Zero, so no surprise that it does not work but I have no idea why before now I didn't see the problem when using these Ender 3 designed mounts with my Mega Zero, even if I'd mirrored the...

:D This is a "small" and simple attempt to build a 3d printer. Small and simple are the keywords here. Just some basic parts to print, standard components you can get anywhere and no special and expensive tools required, as I don´t have access to a...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...

Basic profile: 25% infill, 4 walls, ironing top layers, ...Note: the included images illustrate the goals of the steps outlined below.[ ] 3D Print included stl files[ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan...

3D Printing: The Morse writer telegraph consists of many printed parts that are assembled together. Some of them could have been printed as a single piece. However, I avoided doing so to keep the printing times manageable. Additionally, this allows...

My goal was to make as many of the modifications as possible to be 3D printed parts.Note that in addition to the .STL files, the Fusion 360 file containing all these parts is also provided. Some parts need to be rotated after importing into the...