final fantasy xiv figure 3d models

Now that I do own a 3D printer, I went and created a nice and customizable planting pot to finally make use of that otherwise rather useless down-spout. \o/Since everyone's situation will be different and there does not seem to be a standard when it...

A video is here https://youtu.be/46ky7EqzZt8 When I finally got it assembled, I didn't like the big gap between the block and the intake manifold. So after spending some time looking at similar RX7 engines for sale on Ebay, I designed coils, a...

A standard hex key should be able to reach in and tighten them for final installation.20 mm female-female standoffs are meant to separate the carriage and tool plate, though I believe spacers as narrow as 16 mm may just clear the BLTouch.The tube...

Screw type is not yet tested. Instructions for Power systems coming soon As of now, you must run your power lines in via the GPIO hole. Final Assembly Place the Back Plate on the Shell. Use three (3) M4 x 15mm sheet metal screws to affix the...

Everything fits, albeit with a small rise in the lid for manuals/playboards.My copy of Prophecy of Kings finally came in, so I'm currently redoing the containers as they are slightly small to accommodate the expansion content. (Race boxes, player...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

Note: all spindles should remain installed with or without a spool for the carriage to function properly.The completed dry box can be used from a benchtop (recommend using rubber adhesive footpads), shelf, or you may elect to use the Wall Mount also...

Make sure you do not drill to close to edges, you want part "21" to fit!After drilling the 3,, pilot holes, use a step drill bit to get the final size, 15mm for the middle hole at the side and 18mm for the throughput holes at the front.Jig in...

1) Place your bauble on a sheet of paper 2) Apply glue to the area you'd like to glitter - if working with multiple colors, glue one color at a time 3) Sprinkle a generous amount of glitter on the glued area 4) Collect up any excess glitter by...

After picking up and dropping the project several times, I am very glad to finally be releasing it and getting it off my workbench and mind.My goal was to make the kit simple and inexpensive, so no matter what someone's modding skill set or budget...

Ikea Lack Back Panel I've finally had enough time to start working on the panels. I've decided to continue making sub-things in order to make things a little more organized. Please visit [Magnetic...

My lovely Printables Family <3 THE NEWEST ADDITION TO THE EVER GROWING SELF DEFENSE LINE IS FINALLY HERE: https://www.printables.com/model/704603-night-raids-ultimate-karambit-knuckle-duster-fullyGo show some love to a killer set of knuckles, bottle...

This should create 6 towers of equal heights On top of the 6 Towers put (x6):1x Wood + Wood Stacker1x Wheat + Wheat Stacker1x Sheep + Sheep Stacker Finally, the 6 towers can be completed by placing the 6 player boxes on top (6x):1x PlayerBoxHex1x...

If adjustment is necessary, you can adjust the Drawer_Gap value and the drawer can be re-used in your final print. From v1.1 onwards, the Runner_Height_Multiplier setting enables you to adjust the thickness of the runners. You can increase this value...

And finally, just to give you an example how many tries it took to make things right, check the "failures.jpg" image... ... If you want to make a small donation in appreciation of my humble efforts, please use the "Tip designer" button on this page: ...

So I set out to make and magnetic base and wall system for Axolote Hex.In my magnetic base experimentation I played around with a few different styles before finally settling on one. I created 11 different bases during this process. I've uploaded...

 Finally, you can then move the printer with the PSU out of the enclosure.3. Easy to access the power switch and power socket.  This enclosure has the PSU at the front where it is easy to see and access to both the power switch and power socket.The...

Front panel cover was made to glue on as I was not sure of final design. I do not recommend using current front panel design without modifying MicroSD access as it is currently too tight. Cooling fans bolt to lid and lid bolts to box using M3...

==================================================================== Update 8 August 2021: The "helicopter problem" (the turbine slipping off the bearing when the vacuum cleaner is turned off) is now finally solved with a bearingholder. The...

Similarly, put the other two "3mm disks" on the bottom and the top of the 3d-printed "pointer." Then we have to construct the cap for "pointer+wheels." By using an M2 screw (or a rod) to align the little holes, glue the "wheel cap" with the two "5mm...

Finally, I've posted an extension/cover for the stock on-off switch, because the original switch became too difficult to reach in the new case. PLEASE NOTE: THE CONVERSION PROCESS IS DESTRUCTIVE; THE STOCK CASE WILL LIKELY BE DESTROYED AS A...

mini-torx-screwdriver (flat edge!) Repeat with the other gear Enjoy playing. Post a make or leave a note if you like this design! My first version of me was adding Balls. Now I added a gear instead, as I mostly played with the "hole fillers" I wanted...

A tolerance is possible, as a flat gasket will mask imperfections if they are not too great.Following the enclosed photos, start by passing a nut (domed side) through the ferret head, then a washer and a rubber gasket.Then pass the ferret head...

We will beat this pandemic finally, but let's work hard to minimize our losses until we are there!Print instructionsSimply print all parts in the orientation that I uploaded.I have tested the parts made from PETG on a Pursa i3 MK3S and from PLA on a...

Added 2018-05-006: So finally I uploaded the OpenSCAD files so that you guys can improve this design. Removed 2017-04-14: Removed the old versions, now there are files only for the latest version. I have changed the spec for the threaded rods to 340...

Slicer Orientation and Printing&nbsp;I'll do this in the order the final structure ends up to keep it somewhat logical.&nbsp;Tents should be printed on their thin edge sideBottom Plate should be printed with the open side facing upHex bolt handles...

For a detailed tutorial on building this die, visit my blog: http://inventor-tales.blogspot.com/2012/12/wrapping-up-little-fun-modeling-six.html I've finally finished my gaming dice set with the addition of a 6-sided die, complemented by my existing...

...Finally, Main features thick walls to shield from radiation as well as proper insulation and electrical heating to stave off the cold days and nights of Mars. DRILLING UNIT: The Drilling Unit is the pentagonal structure near Main and the Biodome.

I finally opted for the gu10 system because it is very common in home lighting. I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I...

Scoll down! I will make a post for a suitable stand for the coat of arms the next days. It's finally printed on my Prusa i3 MK3 MMU2 printer. Many thanks to @josefprusa for this great machine!</p> <p>Take a look at the development process on...