fillenium malcon 3d models

The Fillenium Malcon base is designed to support the model at a precise 45-degree tilt, eliminating the need for adhesives or any other form of fastening.

I designed this stand to accommodate a 125% upscaled Fillenium Malcon. It's a flat stand, built specifically to account for the cannons mounted at the bottom of the ship. ... Print Settings Printer: BigBox Rafts: Doesn't Matter Supports: No ...

Wanted a more secure stand than the ones I found, so I made one with protrusions that fit into gaps in the Fillenium Malcon. The 30 degree one is pretty extreme but it's going on a fairly high shelf. ...I'd probably recommend the 15 degree one for most...

This is a versatile base for the fabulous Fillenium Malcon. You can adjust the vassel height and tilt settings. You can secure your Malcon to the stand or, as I did, simply attach some felt pads on top of the three sturdy arms, which provides enough...

Wanted a more secure stand than the ones I found, so I made one with protrusions that fit into gaps in the Fillenium Malcon. The 30 degree one is pretty extreme but it's going on a fairly high shelf. ...I'd probably recommend the 15 degree one for most...

Modified Fillenium Malcon in TinkerCAD: added rear thruster stabilizers (if that's what the little vertical fins in the back are called) changed the angle of the forward wedges to be more realistic; the original Fillenium Malcon had them too skinny...

Fan recreation of a beloved space vessel that's out of this world! This amazing creation prints in place without needing any supports, which is just what I've come to expect from such an incredible design. Printing this beauty may require some...

Hi everyone, I've increased the scale of my Millennium Falcon model by 140%, making it easier to print the parts. However, even with the increased size, I've had issues with poor quality prints due to their small size, which can be time-consuming and...

This is the customized STL rendition of the Fillenium Malcom located at https://www.thingiverse.com/thing:919475, now fully optimized for seamless slicing with Slic3r.

I wanted to print the fillenium a bit larger but with my direct drive my print height is reduced so I cut the model in half and added pin holes to attach the 2 halves together. you may have to play with the pin size to get it to fit. I printed the...

... to the stand later on (allowing me to choose the angle at which the Falcon will sit on it). To get the adapter in place, I had to sand or cut 2-3 edges of it. This stand works perfectly with the Fillenium Falcon at full size, no issues whatsoever.

First Revision of Multi Color Fillenium Malcon Easy Print Remix. Removed Vents, Fixed some Geometry. Final Unit is 150% of Original Scale Legs might still need super glue. ... Credit goes to Multiple Previous Artists.

I built a wall mount specifically for my Fillenium Malcon, but it can easily be repurposed for other ships. My Malcon measures about 15cm wide and boasts a screw hole diameter of 3.5mm. ...This design doesn't require any glue; the Malcon is mounted...

Humans Build Scaffold to Support Awesome Filament Mold Made by Aaskedall, Allowing It to Be Printed Vertically with a Makerbot Rep 2 with Great Results. ... Note in the .Thing File: The Use of Ears is Key to Making the Raft Larger for Successful...

... layer thickness with three outer layers and 15% internal density. ...Standard PLA material works perfectly for these applications. Crafted specifically to accommodate a 200% enlarged edition of the Fillenium Malcon designs available on Thingiverse.

This piece of Filamentum Malcon is carefully divided into seven manageable sections, each securely fastened with precision pins. ...These pins facilitate effortless reassembly once the model has been printed.

This is a Remix of askenall's fillenium malcon which has been split into two parts with easy-to-use pegs for easier printing and quicker assembly. The model as scaled measures 248mm in width and approximately 355mm in length when fully assembled. No...

Yet another remix of the iconic spaceship from Star Wars is unveiled, split and oriented for effortless printing, with each half resting securely on the bed. Alignment pegs guarantee a perfect setup during assembly, eliminating any potential issues.

Just the dish. Cut off the dish on the existing one and print this. No support required. ...Go slow and fine.

Customized version of https://www.thingiverse.com/thing:1935238 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1935238

Just the dish. Cut off the dish on the existing one and print this. No support required. ...Go slow and fine.

I took the front half file from wbrucem and added a hallway and door to the cockpit so it wasn't a blank wall in the back. ... Still throws an error like some of the geometry isn't closed, but was still able to print it.

This is a revised version of askedall's original "space ship thing," with several improvements. The initial models had non-manifold errors that caused problems in some slicer programs, such as Slic3r. I spent considerable time manually removing these...

The Imperium Seizes the Falcon, Turning Rebel Ship to Republic Stand! Imagine if the Imperial forces managed to board the Millennium Falcon and take control of it. No longer would it be a symbol of rebellion against the Empire. The ship's fate would...

This is a simple cut+repair i made in neetfabb in order to be able do print this model in a large scale. i haven't tested it yet, i believe that only the bottom parts can deliver some problems due to weight distribution so will try printing them...

This is aaskedall's original “space ship thing,” with a few improvements. First, the original models had non-manifold errors that caused problems in some slicer programs (like Slic3r). I spent quite a bit of time getting rid of these errors...

I created a straightforward cut+repair in NeetFab to enable me to print this model on a large scale. I haven't tested it yet, but I suspect the bottom parts may pose some challenges due to weight distribution, so I'll start by printing them first.

This thing is a stand for the fillenium malcon it is intended to fit the circular area around the gun turret. The guns fit in the slot cut into the top of the stand. ... It is a minimalistic stand intended to hold up the model without being the center...

I recommend printing it at 1% less than the Fillennium Malcon for best fit.Printed at 119.03% (FM model was printed at 120.03%, which is 1/150th scale).Improved Fillennium Malcon Model:...