filament winder 3d models

I am very impressed with the quality of this filament and love the matte look. I may also give it a matte clear coat to better protect it from stains and marks and prevent any layers from peeling. **Filament used:** [Hatchbox Matte PLA, Olive...

Also thanks for the code of the on screen keyboard!Thanks to ehettervik for the emulator splashscreens.Thanks to ProGM for the GB homebrew game.Print SettingsPrinter:UltiCubeRafts:Doesn't MatterSupports:YesResolution:0.2Infill:20Filament: Filament PM...

RGB definitely isn't necessary but a nice to have in my opinion as different color filament might look nicer with different lighting. Depending on where you mount your Pi, a decently long PiCam ribbon cable. Mine is 1 meter. Amazon link: ([<a...

The pictured stand uses eSun transparent yellow and transparent gray filament. Post-Printing Assembly Instructions Cut the PVC pipe to length. After cutting, you can use some acetone and fine sandpaper to take off any markings and clean up the pipe....

It's printed as two separate parts, which allows you to print the speaker ring in a transparent filament, so that it acts as a diffuser for your LEDs.Even without the use of LEDs, this version has a couple of other benefits. Printing two smaller...

##### Materials: * eSun PLA+ or DuPont Zytel filament (or filament of your choice) * Epoxy (if rail block is loose) * Sandpaper * .75"x1" Aluminum bar stock * M2.5 x 8mm screws (M2 screws can be used but M2.5 is recommended) ##### Tools: * Dremel...

I could have printed the part, but in my experience extruder motors gets quite hot and the heat must be transferred away from the filament, which a metal frame is perfect for. I had much trouble with my Bowden Anet in this department and only an...

The filament im using and what i strongly recommend: https://www.3djake.fi/formfutura/carbonfiltm-black You also need to have some SC/SC6 or RT5 parts for this conversion: - Front lower suspension arms (or Associated T6.2 gull wing front arms). -...

It is available below and on Hume's page: https://www.printables.com/model/199124-adjustable-belt-tensioner-cover-remixPrinted PartsUse the stiffest filament you can. I am using Priline’s Super Hard carbon fiber PC. I found that the structure has to...

you should only have support in the four corners.This part takes about 170 meters of 1.75 filament, about 500 grams, and takes about 3 days to print (for me on my Ender 3, at least), so make sure you only need to print this once!about 30% infill...

This design has been optimized to be printed without supports, and is divided into multiple parts so it can be printed easily.&nbsp;BEFORE YOU START:To assemble this camera, it is required to have printed all the parts and have the following list of...

Sorry for the print quality, I haven't yet calibrated the filament I printed it with (I just wanted to get it printed and running, didn't care if it looked all that good). Vitamins: lots of M3 x 8-14 mm screws 3, M3 x 20 mm screws 2-4, M4 x 30-40 mm...

 See rev2c for these three new parts.I removed the older versions of the STLs to avoid any confusion as well.--Update 7/27/2022:  I did a small test print and found that 1.75mm filament fits snugly in the holes and M2 screws thread in snugly as well...

In the ordinary way this would be a hindrance but here we take advantage of the backlash to create a stomping gait.AlternativeIf you have difficulty with these instructions an alternative is available on:...

The Hero Me Mutant cooling system prevents filament sagging on extreme overhangs in any direction and is capable of bridging 300mm spans with no supports and no sagging. The Hero Me family of cooling systems is considered by many as the best...

I think I will prefer the piece of metal and seal it with filament. I don’t know how that will work in the flex.. I tried melting some flex with an iron and it burnt at the same temp I do PLA with. No science in that test though. I was afraid a...

&nbsp;You may want to print the test piece first, to verify that your printer is accurate enough to print these parts, or to identify a scaling factor that compensates for any issues.Print SettingsPrinter Brand:CrealityPrinter:Ender...

The model’s chosen cutting was aimed at minimisation of the amount of filament needed for generated support. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’...

You can pay with PayPal or your credit card.Watch the tutorial on how to assemble Optimus Prime​ 3D Printing Model at Gambody YouTube channel.Also, you may like Optimus Prime G1 3D Printing Model, as well as other Robot 3D Printing...

0.4mm makes for 2/3 layers at usual layer heights, which is usually enough to bring up the filament color, and not enough to cause problems with the default value for z-hop. The 0.2mm clearance in X/Y helps avoid smearing, and allows for clean...

Be careful to not crush filament sensor cable which is going through the extrusion. Screw Z_motor_mount_L to the place using old M5 screws and then slide the new stepper motor under it. Stepper should be flush with the flat part of the mount,...

The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support, such fine details as antennas, pipes etc. come separately. Model is cut in many assembly parts that are provided in STL files in recommended...

&nbsp;Between the hotend and extruder you need to place a 30mm PTFE piece (OD=4mm) which connects both parts and keeps a constrained filament path.Many components are also connected with melt inserts. Those metal threads can be melted into the...

The attached pictures show the Ad-Mech-Vessel (step less).&nbsp;Print with “Fill Pattern” as "Adaptive Cubic" to save time and filament.No supports are required.Printed at .20mm QualityDoes not open - feel free to remix and make one that...

(Probably more variants in the future, if needed)&nbsp;&nbsp;Print instructionsRecommended Print SettingsInfill: 15 %Layer height: 0,20 mmSupports: No&nbsp;Optional hardwareFor fixing the gridthis: screw 3x16 SPAX (schraubenking) - will slightly look...

The huge battleship model was divided into as many assembly parts as needed to fit even the smallest 3D printers' build plates and for you to nevertheless receive a giant 3D printed ship after assembly. The cutting of the Battlestar Galactica model...

Many more refinements are certainly possible with a full 3D approach now being used, and further design iterations may be made at a future dateThis new build design includes a ‘normal’ plain base with built-in fittings for various battery power...

I ended up using FX-grade gelatine and we melted it in a controlled manner using a 3D-printer heated bed.Print SettingsPrinter:Heavily modded CraftbotRafts:YesSupports:YesResolution:0.3mmInfill:15%Notes:You are going to need a mid-sized 3D-printer...

(AND IF U HAVE BIG PP U'R GONNA USE METRIC SISTEM AND NOT EAGLES PER BURGER) (DAD JOKE FLAG)At leastyou can multiply the m/s by 3,6 for Km/h and by 1,94 for Knots.More update will follow in this days!!Stay tuned!!Update 23/01/24Update the Pluvio-Base...

Except for the figures and token racks which are one-color, all pieces are printed as two-color by changing the color layer by layer (for example, using the M600 command, or manually changing the filament).&nbsp;MANUAL:Game content :- 1x Centre...