filament tube guide for weistek wt200 ideawerk 3d models

To fix this I placed the filament from the spool to the print head inside of a teflon tube so that the distance between the two is constant. This mod uses only 3 easy printed parts and about 70 cm of 2mm ID / 4mm OD teflon tube (about 5 euro with...

To resolve this issue, I positioned the filament from the spool to the print head inside a Teflon tube so that the distance between them remains constant. This modification requires only three easy-to-print parts and about 70 cm of 2 mm ID / 4 mm OD...

This convenient guide clip enables easy delivery of the coil with its accompanying plastic attachment located discreetly behind the printer.

Rather than using the cumbersome "spreading" tubes, I opted to create compact clamps for a more organized setup. ...The new design boasts precision at 0.2mm sliced thickness and an impressive 30% infill rate, ensuring everything is in its proper place.

For Simple Filament Introduction To make inserting the filament a breeze, follow these steps.

When printing, the filament tends to shift from its designated spot, resulting in a consistent problem of breaking off during storage, which necessitates proper alignment of the filament with the extruder at all times.

This design should fit perfectly on the front face of your Replicator 2, and if you have a different model, you can easily modify it to suit your needs.\r\n\r\nWe prefer loading/unloading from the front because passing the tube through the back every...

Human Operator Initiates 3D Printing Protocol at Maximum Resolution Setting. ...Infill Density Set to Absolute Value of 100 Percent. Machine Begins Layer-by-Layer Deposition Process Using Optimized Fused Filament Fabrication Algorithm.

The top is a bit more than half a torus, opened up.I made it because looping the filament over the top of the spool holder, or over that steel plate, seemed to be inviting snags. Modeled in Blender, and run through PrusaSlicer.GCode has a pretty...

I'm Just Getting Started.\nI Added Two Spool Holders Made by SoddOff to My Mecreator 2, But I Needed a Second Tube as Well.\nHere's What I Came Up With.\nPrint Settings\nPrinter: Mecreator 2 Rafts: No Supports: Doesn't Matter Resolution: 0.2mm...

I created this bearing specifically for my CTC A10S.\r\n\r\nI've worked with green PLA to produce the balls, and for added durability, I've utilized airsoft BBs.

I'm thrilled to share this remix from Thingiverse, specifically thing number 2129179. ...It's a seamless fit for the Anycubic Prusa i3 Extruder, which features the MK8 design.

<p>Just print with normal settings (0.20), PLA or PETG would be fine. ...The only other material needed is a piece of standard PTFE tube.Added sliced files for PLA and PETG

I have implemented approximately 16 inches of PTFE tubing (available at http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/PTFE-Tubing-3mm) and two specialized Bowden couplings (also found at...

you will need 1x m310 bolt 35mm(ish) bowden tube and some glue

you will need 1x m310 bolt 35mm(ish) bowden tube and some glue

This is designed for the “Poster” size 3M command strips, part number PH024-64NA,e.g. ...https://amazon.com/dp/B0751VFF2X?psc=1&amp;ref=ppx_yo2_dt_b_product_details .&nbsp;Just put a PTFE tube through the hole and stick it wherever you want.&nbsp;

This is a straightforward support for a Bowden tube designed specifically for the Tevo Little Monster 3D printer. To print it, simply orient the model with the top facing upwards. A brim or skirt is not necessary, unless you plan to use this holder...

It is a bracet I designed to hold both the bowden tube and wires upright. It will keep the plastic tube from rubbing into the wires. ...Just unscrew the old bracet and put this one on. 

Updated 11/26/2017 for slightly wider gap between prongs Remixed from Airmaxx23's great tube holder. I wanted one with as short as possible filament path requiring no extra parts to install, just the basics. Installed on my Malyan M150 but should...

You'll require one Model Six bowden connector, one Model Ten bowden connector, and a PTFE tubing with an outer diameter of four millimeters.

This guide uses the surface between the extruder and the mounting bracket of the extruder. it is 2.5mm thick, so you will have to use longer screws. Also, this avoid the brass lead screw bracket. So no need to use those screws that you want to...

I've just revised the original document using a more precise PTFE tube hole (4.0 mm instead of 4.3). My PTFE tube remains securely fastened to the piece. ...The part doesn't require any screws; it stays in place perfectly with a slight snap action.

A crucial upgrade is needed on the PrintrBot to ensure smooth and precise filament feeding.

... 2.0 enclosure from petitdragen21. ... I made the gap wider, so you can insert a 4 mm bowden tube. I installed a bowden tube between my toolhead an my filabox on the top of the enclosure. As a result of this, i needed a flexible gude for the tube.

This is a filament guide remix for the Voxelab Aquila fitted with a dual gear extruder. Pedrolamas made one for the Ender 3 but the horizontal offset wasn't the same as the Aquila. So I made this remix to fit the Aquila. I hope it helps some of you.

Printed on FDM printer with layer high around 0.2 (0.202 exactly as it is better for my delta printer), and around 0.15 for the screw (0.161 exactly for the same reason). Infill of 30% except screw at 50%. No support. ...Just light sanding on rail...

Remixed the guide from @hamsteyr to replace filament guide with mount to secure the 1/4OD tube right up to the extruder. Had issues with breaking the eyelits from screw pressure from original design, so made it "clip" over the existing screws so...

Remixed the guide from @hamsteyr to replace filament guide with mount to secure the 1/4OD tube right up to the extruder. Had issues with breaking the eyelits from screw pressure from original design, so made it "clip" over the existing screws so...

You will need a pneumatic connector for this to work, I recommend attaching the connector before assembling the holder on the printer as it might require some force to screw it in.Recommend print in 0.16 layer height with adaptive layers enabled (if...