filament spool holder ender 3 3d models

My 3D printer could not hold my large filament spool of 2 kg. ... So I print the extender that fits the ender 3 and ender 3 pro. ...

The Filler spool holder you see in my photos is Filler - Shortened and Curved by uncoild12 thing:4930977 The screws used to attach the Filler to the holder 3 x M3 x 5 Insert 3 x M3 x 20 Screws The screws to attach the holder to the mount 2 x M4 x 16...

After months of printing with my Ender 3, I noticed a recurring issue: uneven filament spool unrolling due to the small diameter of the spool holder compared to the large diameter of the filament spools. This discrepancy causes excessive stress on...

I upgraded my Ender 3 Pro, swapping out a smaller printer housed in a case for this larger machine. To free up space, I had to move the filament reel from its wall-mounted position. The central adapter attaches directly to 2020 extrusions and...

This is a new version of my filament guide (using original 604 bearing) + filament runnout sensor holder (using original Z limit switch) combo but this time used when the filament spool is on the side of the printer and not on the top. It is meant...

This is a new version of my filament guide (using original 604 bearing) + filament runnout sensor holder (using original Z limit switch) combo but this time used when the filament spool is on the side of the printer and not on the top. ... It is meant...

I designed the support from skratches following the very good design of @Boothyboothy (https://www.thingiverse.com/thing:4461496) to extend the support in order to fit the larger 2Kg filament spools.I kept the original concept of being able to re-use...

Two M5 bolts, each measuring 10 millimeters in length, are required. Additionally, two M5 T nuts are also necessary. ...Two more items are needed: M5 bolts that measure 8 millimeters and two M5 hex nuts.

<p>M5 10mm bolt x 2</p> <p>M5 T nut x 2</p> <p>M5 8mm bolt x 2</p> <p>M5 hex nut x 2</p> Category: 3D Printer Parts

This updated model excels in S3D slicing, showcasing significant improvements over its original counterpart.

This is a simple spool holder that fits on the Ender 3 Pro's spool-rack, so it's one part that uses the original endcap that comes with your E3Pro. Its useful for spools with an inner diameter of around 20mm. There's a notch at the end of the insert...

Here is a version of an Ender 3 Spool holder that has Patio Door Bearing Wheels for easy spool rotation along with 3 different spool width shell sizes of 2.0 inch, 2.6 inch and 3.1 inch. The three distinct widths can be used with various spool sizes...

You will need two 608ZZ bearings.

You'll require two high-quality 608ZZ bearings to complete your project successfully. ...The design inspiration for this project comes from a clever creation found on Thingiverse, specifically in thing ID number 3209211.

To utilize this feature, simply print another Creality nut using the Creality (Ender 3) Filament Holder 80mm spools zip file. ... To ensure optimal performance, we recommend printing with four shell walls and high infill to reduce any flex from heavy...

Adaptor for BQ Coil of Filament Holder 80mm Spools By mjoaris Thing Number 3209211

Printer brand: Creality Printer: Ender 3 Supports: Yes Infill: 40% Notes: Print these standing upwards/vertical. ...I printed the FilHolder_80mm vertical with the threaded end on the build surface.

I was looking for a filament spool holder for my Ender 3 S1 to keep the spool centered during prints. I couldn't find one like I was looking so I've designed this one. Also works for Ender 3 v2 (I don't know about other versions though). This a...

Here is all my Side Mounted Spool Holder Ender 3 Pro whole setup after a few tests, and this is what worked best for me: Spool Holder: https://www.thingiverse.com/thing:3646853 The spool holder diameter is 2 or 3 mm smaller than the Ender 3 Pro...

The aim is to use 608 bearings to reduce the friction generated when the spool turns on the stock spool holder that comes with Ender-3. So instead of sliding, now it rolls smoothly, allowing the filament to be fed into the extruder easily without...

The aim is to use 608 bearings to reduce the friction generated as the spool turns on the stock spool holder that comes with ender-3 significantly. So instead of sliding, now it is rolling smoothly, allowing the filament to be fed into the extruder...

This remix removes the little recess at the end of the barrel with the 4 positioning holes so this piece can be printed more easily without supports. To make sure the pins on the stationary wedge still fit they have been shortened a little bit. I...

Caps for the large bolt (Main_Barrel). ...One screwed on the screw, the other inserted into the internal hole.

The first time I printed the FilHolder_80mm_V1.STL the end of it instantly cracked. I made the end thicker for better stability. ... Category: 3D Printer Accessories

When I first printed FilHolder_80mm_V1.STL, the end part cracked very easily. ...so I made it thicker

The first time I printed the FilHolder_80mm_V1.STL the end of it instantly cracked. ...I made the end thicker for better stability.

Part description ==================== The spool holder is a replacement part, which reduces the need for vertical space (you can see the difference between the original component and the newly designed version in the picture above). Functionality...

This uses the stock ender 3/ender 3 pro spool holder bracket and is meant to turn the spool so that it goes straight down into a direct drive hot end.Additional Hardware:1 x m5 nutPrinting:Printed in PLA. Print in the orientation as shown in the CURA...

... used a small plate to brace the bottom, but this is optional. Since this makes the spool clearance shorter, printing very tall objects is not recommended. Modified to use Skrutt84's DELUXE holder (https://www.thingiverse.com/thing:3114139). ...

I created this filament arm/holder as part of my Anycubic Vyper moving into an IKEA enclosure. The original arm was using too much space. I had an Artillery Hornet standing around and used the filament holder from there. Now I designed my own...