filament sensor 3d models

Endstop is connected to a Rasperry Pi running Octoprint, which is handing the correct parking and resuming by using the Filament Sensor Plugin http://plugins.octoprint.org/plugins/filament_sensor . Works with all 1.75 mm filament (you should be able...

This DIY project is a straightforward and uncomplicated filament sensor holder tailored specifically for use with Bowden setups. The design's simplicity lends itself to quick assembly, making it an ideal solution for those in need of a reliable and...

... - have a look on the pictures). ... The filament sensor main body is also updated now. It also seems there was a hole missing - fixed it :) Notes:- There were 2 holes which may need to support, that's now corrected - thx @Locki for sharing the error.

I designed this cover to conceal the Duet Magnetic filament sensor, which I printed in ABS due to its high heat resistance. The print was straightforward, requiring no supports whatsoever. I grew tired of constantly staring at the circuit board and...

I wanted to buy a filament sensor, but I saw that the prices of filament sensors are too expensive for a simple pushbutton or switch, so I wanted to print one myself.I ended up with such a project and I wanted to share it with you on Thingiverse in...

Use hot glue/ super glue as necessary on the lever magnet.(housing magnet will be held into place regardless) Place lever into its proper cavity, ensuring that the top bit of the arm resides within the gap of the plastic prongs on the filament...

This is an holder for the smart filament sensor from BigTreeTech. It is for Ender 3 V2 (Perhaps also for other Ender 3). I have used a littel bit longer screws. Its designed with tinkercad. Now i have tested it. I think it is better if the...

When printing large projects the filament sensor was causing an excessive bow in the filament. This resulted in increased friction and ultimately snapped the filament. I designed this mount to keep the sensor out of the build area and to maintain as...

... the wheel. Add code to Klipper: [filament_motion_sensor FilamentSensor] pause_on_runout: True detection_length: 7.0 extruder: extruder runout_gcode: M118 Starting filament change M600 insert_gcode: switch_pin: !PA4 event_delay: 5.0 Happy printing!

... Duet Laser Sensor v2 - https://www.filastruder.com/collections/electronics/products/duet-filament-sensor M6 4040 T-Nut - https://amzn.to/31J9eot E3D V6 Heat Break (2x) - https://amzn.to/2YSTTVq PTFE Push-In Quick Connect M6 - https://amzn.to/31IsmTK

... that after printing pieces in ABS, the original sensor bracket started to bend and move a lot... So I draw this Filament sensor bracket. You'll need : 3 CHC M3x12 screws for the cover. ...2 little lenghts of Bowden tube I printed it in ABS

I picked up a couple of Sovol SV03 printers and all had had their filament sensors bypassed and when I tried them, the filament was getting a lot of drag due to the sharp angle that the filament entered the sensor. I made up this mount with a 25...

I designed a new filament sensor because my original wore down and stopped working. The filament wasn't making contact with the switch inside, so I took matters into my own hands. After searching for a reliable design, I decided to create one from...

The author of the original filament sensor, which I use here, tested the design with an "1830". For my switch I didn't need any screws to fix the board. Your mileage may vary. I removed the cable guides, as i don't need them. These are my first steps...

Here I bring you a small solution for that Creality CR-10 V3 filament sensor that produces too much friction. Having it at the top can cause a possible breakage underneath the sensor, the printer would still work without detecting it. It connects...

When I changed the factory extruder by a BMG-like one which is bigger, the filament sensor did not fit. So I designed this simple adapter.It´s needed tho small M3 screws to attach it to the printer in the former position of the sensor. ...Then attach...

It is very difficult to see and harder to adjust the idler screw located under the PTFE tube going to the filament sensor. This design moves the filament senor up where it is much easier to both see and access the idler screw.The holder for the...

My CR10 v2 filament sensor was unreliable to say the least. I made this shim to go under it to help keep the little lever alighned. It fit my printer well and solved the problem. I don't know what else it would fit. I would recomend doing it whether...

I bought an original filament sensor from Creality itself but I didn't want to disassemble the whole printer to attach it. So I designed an addon for the Filament Guide, designed by Filboyt. (https://www.thingiverse.com/thing:2917932), so I can easly...

Without this, the filament sensor output is loaded by the thermistor input and the output signal is reduced, leading to inaccurate output. ... This is not needed for a general purpose analog input because the current draw is very low for these inputs.

... thermistor input. Without this adapter, the filament sensor's output is loaded by the thermistor input, resulting in an inaccurate output. ... This adjustment is not necessary for standard-purpose analog inputs since their current draw is very low.

I installed a custom filament runout sensor based on Laubed's design, adapting it to fit snugly onto the extruder support with an added flange for extra stability. ...The modified sensor is now securely fastened to both the extruder flange and two of...

I just recently installed Dickmasta's "Sidewinder X1 Spool Holder Fix" (https://www.thingiverse.com/thing:3650974) and quickly realized the filament runout sensor was poorly positioned, so I designed this bracket to relocate the sensor in a much...

The only thing I haven't liked about the Base upgrade for my Mini has been the mount for the filament sensor.  So I created one without the need for the tie-wrap. ...I printed in PLA on my Mini with no issues, and reused the cover and internals...

This bracket is designed specifically to house the Triangle Labs Filament Sensor, offering a precise fit. To accommodate printing with PETG and poor bridging, I printed mine straight up with the sensor opening pointing upwards, resulting in a sturdy...

Introducing the Bowden Breeze, a game-changing filament sensor add-on that simplifies your 3D printing experience like never before. This ingenious device attaches seamlessly to your existing extruder, providing real-time monitoring of filament...

This is a remix of an excellent filament sensor found here (with more info and instructions): https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/al3ph/filament_runout The only thing it was missing was an easy way to mount it. ...

Hello, today I'm excited to share this support for the filament sensor with all of you. The distance between the reels is a little larger than the width of the filament roll, and I think you'll really like it. You might need to make the screw holes...

Prusa i3 MK2.5s and MK3s Pneumatic Coupler Filament Sensor Cover Replacement. I install a guide tube from my dry box where spools are stored to the printer, allowing the tube to clip directly in. This prevents the weight of the tube from stressing...

I used more stock Q5 screws to mount the filament sensor (m4??), and have designed the model to accept these large screw heads and provide a bit of play to get it seated correctly. Filament sensors are easy to pick up online cheaply and plugs...