filament sensor ender 3 3d models

you need to install some filament sensor plugin with GPIO support In Plugin settings, choose the board pin you are using, the switch type, and make sure "Pause print when out of filament" is check marked. You may leave debounce time unchanged and...

This is a remix from https://www.thingiverse.com/thing:4014649 more fittable for allmetal extruder assembly, the filament is more stright to the hole of the chinese metal assembly leading in less filament friction

I had a spare microswitch for the Z-stop after installing a BLTouch, so I made it into a filament run-out senser, re-use the factory screws and mount to Z-axis where the lead screw mounts.

2023.3.1 Update Added for 4mm PTFE Tube. ... Required Parts ・M3x4mm Insert Nuts　x2 ・M3x6mm Insert Nuts　x1

You must have - 3X M3 20mm screw - 2X M3 nuts - 1X M3 self-locking nut

I like KaminoKGY's design, but the lower bolt slot turned out to be a weak spot that kept snapping on my setup, so I used Tinkercad to fuse a 2mm-wide bar across the mouth for reinforcement. It doesn't interfere with the Z lead screw, and there are...

I remix this 2 projects for my own https://www.thingiverse.com/thing:4808355 https://www.thingiverse.com/thing:5789436 now i have a movable holder printed with support

Human: Required 2x Micro Switch v-156-1c25 or other option available at Aliexpress 2x M3x10 screws 4x M3x15 screw and nut pairs 2x M5 screws 2x M5 T-nuts

This is a remix of the Filament Guide for Creality Ender-3 or CR-10, https://www.thingiverse.com/thing:3052488 from Holspeed. I added a Filament Runout Sensor to the design. The switch must conform to DIN 41635 standards, featuring a roller lever,...

Filament guide for your Ender 3 Pro with the ability to place your filament runout sensor.3 versions:1 filament guide1 filament guide with runout sensor1 filament guide with runout sensor and extra supportprint with 20 procent infill and your good to...

Simple filament sensor mount for Ender 3 V3 SE.Designed for sensors shaped like the "BIQU 3D FILAMENT RUN-OUT DETECTION SENSOR MODULE" or this one: https://www.amazon.com/gp/product/B07F65TXGS/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1I used a...

Simple filament sensor mount for the Ender 3 V3 SE (maybe other V3 models as well). Uses brass insets for the screws. I have included the step and parasolid files so you can remix it to suit your needs. Amazon link to the sensor that I will be...

Then run Input Shaping and we're done!EdinBearDragonE3V3 CollectionThis is part of a collection of Ender-3 V3 Mods, designed to fit with the aesthetic of the printer.Ender-3 V3 Top Spool Holder (Rear Facing)Ender-3 V3 Top Filament Sensor...

I had been using the, excellent, filament sensor bracket by Jack1961 but when I updated to the all-metal, duel cog, extruder (illustrated) it no longer fit. I, therefore, did a remix to match this extruder. I have included a photo of the sensor...

Version 2 of my filament runout sensor using the Ender 3 Z endstop. https://www.thingiverse.com/thing:4614544 Improvements are: -Thicker bottom shell. -Requires two 7.5-8mm pieces of PTFE tube to reduce friction and improve longevity. ...

Rotating filament run out sensor mount made for my Ender 3V2 after I fitted a direct drive Sprite Pro extruder.All 3D printed except for 4 threaded inserts, 5 screws and a t-nut.I replaced the stock 4 screws that come with the filament sensor with...

Simple, easy to print, easy to install/remove Smart Filament Sensor holder that attaches to the 2 M3 screws of the lead screw nut. I'm using dual gear drive extruder, but i think i should work on standard extruder too. I've drilled a 4mm hole in the...

I also subtly adjusted the position of the filament tunnel, ensuring it's now aligned directly with the stock Ender 3 extruder. I highly recommend printing with supports and zero infill. Utilize the stock Z endstop button and your preferred cable to...

The connector on the motherboard is a 4 pin but i modified the 3 pin on the included cable to fit on the 3 left pins on female connection at the motherboard.The KE version of this printer has the sensor pluged in at the same connector!If you connect...

I made this bracket to work with my direct drive setup on my ender 3. It clips around the stepper motor so its very easy to install. The bracket fits pretty snug so it wont pop off while printing. ...It does reduce how high you can print but you can...

Normally, the filament runout sensor is directly screwed onto the filament spool. After I built a enclosure around my printer and placed the spool outside the enclosure, this was no longer possible.This sensor holder can be clicked directly onto the...

 But afterwards I bought Creality's filament runout sensor, and couldn't find a good place to mount it that wouldn't interfere with my existing reverse bowden setup.  So I solved two problems at once: runout sensor is inline with existing filament...

I'm remixing the Bondtech BMG dual extruder design to utilize a widely available Chinese filament sensor from AliExpress, replacing the original CR-10 filament sensor that I don't have on hand. The resulting design should be compatible with most 3D...

Attach to the extruder bracket via the brass z-axis nut. ...See pictures for illustration. Amazon Filament Sensor: https://www.amazon.com/gp/product/B08QJDSZCL/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

The roll will guide the filament into the runout sensor and from there into the extruder. I designed this based on the remixes mentioned. You can take out the runout sensor from the original CR10s and place it into this design. ! Print the...

To observe and react to the switch, I used an octoprint plugin called Filament Sensor Reloaded: https://plugins.octoprint.org/plugins/filament_sensor_reloaded/ Alternately if you aren't using octoprint, I guess you plug it into your display...

Changes From the Original: I imported the original .stl files into Fusion360 and tried to recreate an exact match (so measurements and fillets aren't necessary the exact same, but should be very similar) - Angled the Filament Sensor in such a way...

I've drilled a 4mm hole in the extruder arm, and used a short piece of PTFE tube to connect the sensor and extruder together for easier filament loading. The fit is quite tight so you might have to experiment with scailing the model or using...

The red aluminum extruder upgrade is pretty common for the Ender 3, so I think the design will be useful for a few people. Furthermore, I removed the logo on the Cover. Not to violate any type of copyright, but to make it easier to print, since I...

Runout Sensor Mount --------------------- I'm using the filament sensor from TH3D, which mounts easily and securely using a couple of long 3mm bolts. I've gotten away with not using nuts (the threads are catching on an exposed bit in the body of the...