filament roller ender 3 3d models

https://www.thingiverse.com/thing:5238538

I highly appreciate the assistance offered by Tomaskom_cz, but I needed an alternative that would fit on the front side since a Z-axis support was installed. ... Please print this design just like Tomaskom_cz's original file for optimal results!

Filament guide roller I designed for my Ender 3 Pro. After a seeing lot of 'filament guides' on the net, nothing seemed great to me. Hope this finds useful to many. My Thingi features: No bearings, No screws, only 3 printed parts, easy slide fit. ...

10mm longer version of Ender 3 Pro Filament Roller and Guide (20201205 ver 1.2) by broosed

Filament roller guide for Ender 3 that requires no bearings or assembly. Simply print the part, snap the roller loose and bolt it onto an existing bolt near the stepper motor. The roller must face downwards on the print bed in order to be printed...

I've been in need of a filament roller guide that allowed to feed from both top and bottom into the extruder , without any extra resistance so I designed this : Ender 3 double filament roller that allows feed from both top and bottom ! No extra...

This is a combination of two separate files, both considered the most effective solutions for filament handling on the Ender 3 in my opinion. I am not an engineer and have very limited experience with 3D modeling, so this is essentially a patchwork...

... by holspeed. ...In my case i've to feed the filament from the side due to space limitations. I just turned the roller in a was that it suited my needs. ...You can find the rest of the needed Parts here: https://www.thingiverse.com/thing:3052488

In my case i've to feed the filament from the side due to space limitations. I just turned the roller in a was that it suited my needs. ...You can find the rest of the needed Parts here: <a...

... be printed without support. The only support needed should be down in the little cutout, where the pin gets inserted. **----** Added improved version of the roller preventing the spool from falling down. ... Step file for roller and stud included.

Here is a small modification of an accessory already found on this platform: https://www.thingiverse.com/thing:3052488 - thanks go out to the original creator. ...I made some changes so that it can now hold a hard drive read head bearing, effectively...

The bracket is 11mm longer, to align with Bondtech BMG. ...Everything else is the same.

Remix from https://www.thingiverse.com/thing:4683505 by Markacho. ...and just extended it 35mm to prevent it from collide with Z-brace support.

Basically this is just another remix of Holspeed's https://www.thingiverse.com/thing:3052488 with the same arm design. I don't have any bearing with me, so I reduced the hole reserved for bearing to M4 size since I have some M4 screws lying around. ... ...

I didn't have access to a standard 608 bearing, so I redesigned the part in Solidworks to accommodate a 6200 bearing instead. The ring fit snugly, but everything assembled smoothly nonetheless. ...A UNC #10-24x1 machine screw secured all the components...

https://www.thingiverse.com/thing:3052488 has been on my E3 pro for 100s of hours. ...So when I went side mount for my spool I had to remix and print a new double bearing.

I made some modifications to allow a bearing roller to be used, and as a bonus, I included the roller right here in the file. All you need to do is pick up two skateboard bearings, and you'll be good to go! This thing is seriously awesome, and I'm...

Remix of - https://www.thingiverse.com/thing:5388236 Edited the guide arm to align better with my Ender 3 Pro. Original had a tendency to have the filament rest on the edge of the guide (sometimes between the roller and the guide frame). Should fit...

You will need: x2 spacers x1 bearing v ring x1 filament roller arm x1 M416 screw x1 608 bearing F3D file included. ******************************************** Added a short version with the roller closer to the frame. ... Original Part:...

Remix of HugoHuge and mjoaris's Filament Holders designed for easier printing, compatible with smaller spool diameters, and featuring a secure capture system that keeps the 608 bearings in place to prevent the roller from falling out. Best results...

I updated the design I shared a couple days ago to make it entirely printable, including the wheel and all its components. To print it, I positioned the axle shaft vertically and didn't use any supports; instead, I had to trim some material from the...

Here is another remix ! Other ones didn't fit on my E3v2 - this one has larger opening to fit better on the metal piece. It's made to fit smaller bearing (606ZZ I had in stock) indidebearing piece : the hole is a little tight - has to let...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

I remixed both design and attached them each other. ring and spacer are from other design. 608zz bearing, 1 bolt and 1 nut are required to assembly. ... Thanks for the designs.

I enjoyed the roller guides from https://www.thingiverse.com/thing:3052488, but I found it annoying that you need to thread the filament through the roller, and can't add/change the roller with filament already installed. So this is a version that...

Just the rod protector for those who already have a roller. Hope it helped! Apenas o protetor do fuso do eixo z, para aqueles que já tem algum rolamento impresso. ...Espero ter ajudado!

Just the rod protector for those who already have a roller. Hope it helped! Apenas o protetor do fuso do eixo z, para aqueles que já tem algum rolamento impresso. ...Espero ter ajudado!

Simply a remix of the LEGENDARY! ..."Ender 3 Filament Roller Guide" from Holspeed to replace the metal bearing with a print in place bearing. ... The bearing source is https://www.thingiverse.com/thing:53451

This is a remix of: 3: https://www.thingiverse.com/thing:4662740 2: https://www.thingiverse.com/thing:4185537 1: https://www.thingiverse.com/thing:3052488 The Original one from BrendanShanahan (thing 3) was build for the Ender 3 V2 with aluminium...