filament guide tube 3d models

A Customized Refurbishment of a 2020 Snap-On Filament Guide for Enhanced Creality Printer Performance. ... I Made Significant Changes and Added a Precise PTFE Tub Insert Hole, Ensuring Smooth Filament Flow by Preventing Grind-Inducing Friction Against...

This is a filament guide remix for the Voxelab Aquila fitted with a dual gear extruder. Pedrolamas made one for the Ender 3 but the horizontal offset wasn't the same as the Aquila. So I made this remix to fit the Aquila. I hope it helps some of you.

Remixed to match the look of the other design (tube/filament guide), just used the "clamp" part. ... Printed a pair of tube guides because my spool sits on the table near the printer, not on the top.

Without that guide I had some problems. ...Just insert some teflon tube for best results.

A model for fixing a tube for a filament. The coil does not unwind when lowered. (my English is bad).Фиксатор трубки для филамента. При использовании одиночной катушки есть вероятность разматывания прутка когда печатающая голова опускается. ...В эту...

Angle needed to give a more direct path of the filament to the hole in the extruder, so less friction. Screw holes removed as they were not needed on my printer. I've included both a 3MF file and the old STL file format. ... ...

Wanhao D6, MonoPrice Maker Ultimate, MK11To have a more stable feed and less ribbon flop. ...fewer accidental stops.I have 2 on my ribbon cable worked out great.

Wanhao D6, MonoPrice Maker Ultimate, MK11To have a more stable feed and less ribbon flop. ...fewer accidental stops.I have 2 on my ribbon cable worked out great.

This is a quiet non-squeaky Filament Guide for the Ender 3 because we utilize PTFE Bowden tubing to guide the filament with ease, resulting in complete silence. You should have some extra PTFE Bowden tubing on hand. This setup also enables effortless...

Primarily, it prevents wear to the filament sensor housing by guiding the path of the filament with a length of PTFE tube on the input. It also helps reduce air exposure to humidity-sensitive filaments like PETG and Nylon by keeping the filament...

Using ideas from other designs, I added a funnel on the spool side to make loading filament easier and made sure my new 1/4-inch OD PTFE tube fits snugly into the bottom and stays there during printing. Then, I added a retaining ring on the bottom to...

🙂There is a bowden tube filament guide arm for the Creality K1.It can be mount on the place of the 2 existing screws.Unfortunately they are too short, so you can't reuse it.You will need a new 2 longer screws (M2.5 - 1.5 mm length).It can be mount...

I have used about 40cms of PTFE tube (http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/PTFE-Tubing-3mm) and 2 Bowden couplings (http://e3d-online.com/RepRap-Spares-Mechanical/Bowden/Bowden-Couplings). I recommend some double side tape to avoid...

Remix of https://www.thingiverse.com/thing:4504481 and https://www.thingiverse.com/thing:4175157. ...With a additional support leg and a hole for bowden tube 6mm.

Remix of https://www.thingiverse.com/thing:4504481 and https://www.thingiverse.com/thing:4175157. ...With a additional support leg and a hole for bowden tube 6mm.

Here's a quick fix to shrink the hole down to perfectly accommodate a 4mm tube. Just remember, you'll still need 3mm wide zip ties if you decide to use them. ... edit: I made a mistake earlier and referred to 3mm as a tiny detail.

<p>Made for 3030 extrusions and M6x12 screws</p>

E3D V6 Bowden X Carriage with Enhanced Filament Tube Support Now Easier to Install This mounting guide has been reinforced for increased durability and stability, ensuring a seamless printing experience. ... Print Settings: * Infill: 50 - 100% * Layer...

This filament guide will guide the filament smoothly into your CR-10 Max, preventing the filament from scraping against the filament sensor as it enters the Bowden tubing. Setup: Print the guide, then insert a few inches of Bowden tubing into the...

Allows you to fit the spool holder facing forward on an Ender 3 v2 3D printer and prevents the filament bending around the lead screw by using a reverse bowden tube to guide the filament to the extruder. I use reverse bowden tubes from a dry box,...

Allows you to fit the spool holder facing forward on an Ender 3 v2 3D printer and prevents the filament bending around the lead screw by using a reverse bowden tube to guide the filament to the extruder. I use reverse bowden tubes from a dry box,...

I integrated modifications to merge filament guides, allowing me to also attach a PTFE tube using an M6 fitting.

Remix from https://www.thingiverse.com/thing:1358776 Die Halterung wurde für den X1 angepasst mit einem Überstand mittig zu Extruder.

Remix from https://www.thingiverse.com/thing:1358776 Die Halterung wurde für den Genius angepasst mit einem Überstand mittig zu Extruder. Es ist vielleicht ratsam, die Auflage zusätzlich durch ein dünnes doppeltes Klebeband zu fixieren. ... Mehr...

......I've been using this for years anywhere that the printer has a PTFE tube as the inlet for filament and it makes life much easier when you're feeding in new filament.Printing is simple, print the large end of the funnel face down. No supports needed.

I'm definitely experiencing vision loss; however, I've grown tired of struggling to insert the filament into the tube opening for loading into my extruder, so I came up with this tiny solution.\r\nFeel free to modify it if you have any suggestions to...

for 4mm PTFE Tube. use a 4.1 mm Drill . ...

The cooling feed tube prevents filament premelt while a cooling tube mount blows air across the build plate for PLA use. Silicon cable ties hold tubes in place, and a foam block with a hole collects dust and hair. ...A compressor in the garage supplies...

Don't forget to hit the like button if this helps you :)&nbsp;A filament guide for the Ender 3 S1 gantry top rail, remixed to enlarge the hole through the eye of the swivel to be larger so its supports some PTFE tubing. &nbsp;OD 4mm is a nice snug...