filament guide tube 3d models

This is a straightforward support for a Bowden tube designed specifically for the Tevo Little Monster 3D printer. To print it, simply orient the model with the top facing upwards. A brim or skirt is not necessary, unless you plan to use this holder...

Hello :) This is not the final project yet, but it works and improves the work of the machine. Final project soon. ... Material: PETG orange DEVILDESIGN Filling: 20-30% Speed: 80mm / s

A guide that hooks onto the end of the x-axis and accepts PTFE tubes so that filament arrives near to the feeder intake.

Remixed from a popular filament guide, I discovered the hole for the tube was slightly too small to accommodate any of my PTFE tubes. To address this issue, I modified the design to fit the Capricorn PTFE tube at 4mm in diameter, making it suitable...

Remixed the guide from @hamsteyr to replace filament guide with mount to secure the 1/4OD tube right up to the extruder. Had issues with breaking the eyelits from screw pressure from original design, so made it "clip" over the existing screws so...

Remixed the guide from @hamsteyr to replace filament guide with mount to secure the 1/4OD tube right up to the extruder. Had issues with breaking the eyelits from screw pressure from original design, so made it "clip" over the existing screws so...

If you're looking for an alternative to PTFE tubes, or they weren't bundled with the printer, this could be your answer.

This is a 45 degree version of the "Drybox filament guide using PTFE tube" made by @mp42, available for OD4mm and OD3mm PTFE tube.If the inside diameter of the fitting is too tight, it may need to be adjusted.

Please find the free models here: https://www.printables.com/model/374779-ender-3-v2-dual-extruder-filament-guide-for-ptfe-t _____ Used the original filament Guide from Soda Surfer / RedSoda for 2 years and recently upgraded to a dual extruder. As my...

### **This now lives on [Printables](https://www.printables.com/model/347665-ender-3-v2-filament-guide-with-bowden-tube-support) and may not be up to date on Thingiverse** None of the existing filament guides I found were quite what I needed so I...

To assemble this guide, you'll need: * 1x M3 15 mm screw * 1x M3 washer * An 8 cm filament tube (such as a standard 1.75 mm tube available on Amazon) Cut the tube using a sharp knife or carpet cutter, taking care not to compress or deform it during...

... tube guide, clamps, and wiring gap. To install, remove the stock head and right filament, snip the right filament tube guide, and any spacers. ...Clamp the print around the fan, feed filament and guide into the holder on top, and zip tie wires.

... in. ...To guide the filament into the printer, I employed a 2x4 PTFE tube along with a push-through fitting.\r\nThe images depict a previous iteration of it; I haven't printed the updated one yet.\r\nFeel free to try it out and modify it as needed.

Ender 3 pro filament guide for PTFE tube It works with Ender 3 pro genuine Bowden plastic extruder or metal extruder like in the picture.I prefer this design over the bearing roller type, less inconsistent friction.You should print like the last...

DrStreet's design from https://www.thingiverse.com/thing:2873157 came closest to meeting my needs, but after two months of use, strange noises started emanating from the filament during retraction and I noticed that the guide was worn out because the...

Holds up to 6 connectors, clips to the existing spool holder vertical arm on the i3MK3S.I needed something simple to guide my filament tubes from my dry box to a usable position above the Prusa print head. ... I really did not want to have to keep...

... Beugel" beerbottle). Drill out the center hole with a 4mm wood-drill, Insert a 4mm PTFE tube and you're ready to feed some filament to your printer. ... Tip: If the threading gives you a bit of trouble, apply a bit of grease to the inside Nut.

Here's a guide for building a filament guide that makes use of the holes in the back of your CTC dual printer: this is possibly utilized for cable ties. To get started, print out two clips and attach them securely to the printer. When attaching these...

I noticed that when printing large objects, the head moves left and right, causing the filament tube guide to sway quite a bit. If the connector of the tube meets the hot end as vertically as possible, maybe it will help reduce clogging - that's just...

......A PTFE tube, cut from a CR-10 spare part, was being used. There's a slight issue when removing filament as the blob portion won't retract back through the PTFE tube. ... A few upgrades for the CR 10, including some hop-ups, are available on eBay UK.

Because of humidity issues with a PET-G filament spool, I created a dry box for my filament rolls with a feeder and teflon tube. I engineered this attachment point to fit perfectly on my printer, positioning it high and centered above the extruder.

Here's a custom-designed filament guide tailored specifically for the Creality CR-10 3D printer. To get started, you'll need to carefully tap it into place using an M6 tap set - you can refer to the attached photo for a clear visual reference. ... For...

... Then, insert a 4mm PTFE tube and you're ready to feed your printer with a steady supply of filament. ... A helpful tip: if the threading proves tricky, try applying a small amount of grease to the inside nut for an easier assembly process.

2020 Aluminum extrusion mount filament tubing guide/holder to complement the 20x20 (2020) Vertical Mount Side Spool Holder; thing:4581676. The mounting bracket is visually the same style as the filament holder and will attach using M4 x 8mm Flat...

2020 Aluminum extrusion mount filament tubing guide/holder to complement the 20x20 (2020) Vertical Mount Side Spool Holder; thing:4581676. The mounting bracket is visually the same style as the filament holder and will attach using M4 x 8mm Flat...

So I had the idea that the filament sensor must be guided at an angle to the DD extruder to avoid plastic abrasion on it. I quickly came up the first design in which the adapter is screwed on with one screw and the sensor is screwed to the adapter...

2020 Aluminum extrusion mount filament tubing guide/holder to complement the 20x20 (2020) Vertical Mount Side Spool Holder; thing:4581676. The mounting bracket is visually the same style as the filament holder and will attach using M4 x 8mm Flat head...

Hello, This is a PTFE tube holder to guide the filament It use a PTEF tube holder / https://aliexpress.ru/item/32959601701.html?spm=a2g0v.12010615.8148356.47.22dd53b0bXdYBK For the screw /...

In collaboration with Thingiverse's URL - https://www.thingiverse.com/thing:392784 - we're moving forward together to create something entirely new.