filament enclosure 3d models

This can pause your print when your filament runs out.

I created this guard to stop my pets from attacking the filament as it enters the top of my enclosure. ...It does not lock, but it is enough to obstruct the filament so my pets ignore it. Future plans: I may create a remix that attaches the the...

Filament-guided enclosure for a Prusa I3 MK2 with horizontal spool holder on an IKEA Lack frame.\r\n\r\nPulley:\r\nhttps://www.thingiverse.com/thing:2540231\r\nUniversal spool holder:\r\nhttps://www.thingiverse.com/thing:508896\r\n\r\nKudos to the...

Filament Guide for a Spool Holder on Top of an Enclosure. The Concept Aims to Halt Filament Drag as the Spool Decreases in Size. ...The Wheel Design Originates from the Ender 3 Side Filament Guide Available at https://www.thingiverse.com/thing:3052488

Same as the original just with some filament removed. ...I have printed and they print just fine Print instructionsFollow the instructions of the original model.

I recently upgraded my spool holder, realizing that the original design wasn't strong enough and needed better positioning to fit seamlessly within my printer enclosure. I'm fairly certain there are two usable sets of holes, although I'm not entirely...

For the user of snapmaker 2 who has space constraint for enclosure. ... This reuses the original filament holder part of the enclosure.

... ...If your spool sits outside the enclosure, this setup will efficiently clean dust from the filament before it enters the enclosure. To improve airflow, attach an M5 pneumatic connector at the bottom and guide it through a PTFE tube to the extruder.

This is an INTERNAL (goes inside the enclosure) filament spool holder specifically for the MatterHackers "CR10 Enclosure". I designed it to be strong and printed without supports (sans the "Filament Holder" component which I didn't design). I...

My requirements for the filament runout sensor enclosure: 1. The enclosure must be mounted directly to the printer, eliminating any loose or dangling connections. 2. Wires should exit the back of the enclosure to avoid interfering with the x-axis. 3....

This is a filament sensor cover for MK3S+ models with the Bondtech Mosquito upgraded extruder.  It is meant to be used in the official Prusa enclosure.  It will require removing the brass insert from the cover supplied with the enclosure.

I wanted to mount the CR10S filament sensor above my custom-built enclosure. Since I couldn't find an acceptable solution, I adapted the design from https://www.thingiverse.com/thing:2875859 into a simple yet highly effective top filament sensor...

This turns your printer enclosure into an efficient filament dyer, as it stays about 46°C (116°F) when the bed is set to 90°C and all the doors are closed. For installation, you need one 2020 t-nut with M5 screw hole, and one M5x12mm low-profile...

I was having issues with the MMU2S, so I wanted to design a simple filament guide that feeds the filament directly above my printer through the lid. The guide is short and meant for Lack enclosures that have been prepared for the MMU2, where the...

Most filament guides I found were just plastic conduits through the lid, and in my experience the filament scratching across the plastic gets amplified like crazy by the enclosure.So I came up with this idea of running a PTFE tube through a conduit.

Most filament guides I found were just plastic conduits through the lid, and in my experience the filament scratching across the plastic gets amplified like crazy by the enclosure.So I came up with this idea of running a PTFE tube through a conduit.

Useful if you have the LACK enclosure v2 but not the MMU.I finished building the LACK enclosure v2 and was looking for a nice way to get the filament inside without going through the back (I do have the MMU2 but it's still sitting unassembled in its...

I like it but I hate the fiddling required to put spools of filament onto the included filament holders. So I decided to make a new remix of the spool holders I use for all my other printer brands, [spongybob1958's TUSH2...

This is an easy to print and easy to assemble filament guide for the [Prusa Enclosure V2 - MMU2S](https://www.prusaprinters.org/prints/3673-prusa-enclosure-v2-mmu2s) with the filament on the top Lack table. It is designed for 1,75 mm Filament. This...

I like it but I hate the fiddling required to put spools of filament onto the included filament holders.So I decided to make a new remix of the spool holders I use for all my other printer brands, spongybob1958's TUSH2 design. It's super easy to...

I added feet so I can place it on top of the enclosure, and now I can store as many spools as I like - all thanks to the adjustable rod length. To build this masterpiece, you'll need a few extra parts: - 608 Bearings - four per spool, because why...

Upcoming Revisions: -Install a 120mm fan and duct to the window (STL is provided) -Add a clear door -Secure the filament tubing BOM: 2 x Ikea Lack tables Multi-color LED USB 2 x 5mm Bore Aluminum Toothless Timing Belt Idler Pulley for Filament Guide...

I've always been plagued by a mess of filament strings piling up around my printer, especially on the nozzle side. To keep things tidy, I designed this little dump bin as a catch-all for all those strings. It's 45mm deep, which makes it fit perfectly...

<p>The bowden fitting is very firm, you might need to use players to push it in. If your print tolerances are a bit off. ...Use a 4mm drill to remove the excess from the print walls for the bowden fitting.</p><ul><li>Print it flat with no...

So I drilled a 10mm hole into the middle and created a filament guide/funnel, which will be pushed from the top into the enclosure. The second part is a filament-runout sensor bracket. This part will be pushed over the funnel and locks both in...

Designed for 6 spools.Recomended print settings:Print with PETG, 3 walls, 25% infill.Instructions:Make o hole in the roof ikea lack enclosure to fit the “lack cover top”. Glue “lack cover bottom” at the bottom. Install in (Un)original Prusa Drybox...

... so is designed this to match my setup. On my rail I have another one, in case I am storing a filament next to the printer for regular printing (the ones I use rarely), so you can use them for anything you feel like. ... Hope it helps someone!

This is a simple design to allow for the internal mounting of the included Snapmaker 2.0 Filament holder bracket to be mounted inside the Enclosure. This allow for a clean external esthetic as well as it keeps the spool up out of the way tucked into...

A filament passthrough for the IKEA Lack enclosure with threads for a PC4-M10 bowden fitting. Rotate file 180 degrees and print with a brim and supports touching buildplate only. ...See picture for example. Print Settings Printer Brand: Creality...