filament enclosure 3d models

This is a filament spool stand designed for holding filaments spools on top of an enclosure, specifically created for the IKEA LACK TABLE Enclosure. The original holder was problematic due to its tendency for the spool to fall, as it simply sat on...

Block mounted with M4 screws to the top of my printer enclosure to insert the 8 filament feeds in a decent way. ...I used the following hose set: https://www.amazon.de/dp/B07PV9LCLYPrint SettingsPrinter Brand:PrusaPrinter: I3...

Hi, this is my second filament grommet, for the Snapmaker Original enclosure, version 1 and 1.1. Made it larger, for easier handling, and gave it a slight flange on the input side. Glue only the input side to the tube, leave the output side just on...

This part is intended to be used outside of a printer enclosure to cover up the hole for the filament insertion. At the same time it can act as point of attachment for the filament tube. It has a 5,5 mm diameter hole on one side. A PC-4 M6 push...

The silders are meant to let the filament flow where it wants while still restricting it from slipping out of the wheel/pulley and avoid friction. Sliding up and down accomodates different height spools and also the difference in height of a full...

**ORIGINAL** I installed the "Self-adjusting filament guide for Ikea Lack table enclosure" (link below) but, being as I'm very frugal, I didn't have the correct size hole saw and drilled the Lack table a bit too large. So 30 seconds in Fusion 360...

I have built the Prusa i3 MK3 enclosure - Ikea Lack table which is awesome. However, I was not satisfied with the filament feeder tubes, especially when the extruder is near the topmost position. Here is my take on a solution for feeding the filament...

This is an enclosure designed specifically to house an optical filament run-out sensor. The central section allows for some adjustment if the sensor comes poorly soldered and thus in the wrong position, as I encountered myself. You will need an M2...

Abstract: A simple, easy-to-install filament feed hole for the IKEA LACK table, often used in printer enclosure construction. Brief: I designed a filament feed hole that's small, tidy, and straightforward to install, eliminating worries about...

Wanted a passthrough that would accept bowden tubing through the top of an ikea lack enclosure for my direct drive ender 3 v2.

This is a remix for the pins on the prusa lack enclosure so that you can use it with 608 bearings. ...You will need to push the bearings in a bit, they don't fit flush.

... to secure it, and feeding the filament through the sensor housing was a real challenge. Based on these issues, I made two key changes - adding walls to stabilize the switch and incorporating a tube to guide the filament smoothly through the case.

... Considering these two issues, I made some key improvements. First, I added two walls to secure the switch and ensure stability. Second, I incorporated a tube that guides the filament smoothly through the case, making the filling process much easier.

For info to incorporate this into a Robo 3D R1 see: http://community.robo3d.com/index.php?threads/filament-runout-sensor-frs-upgrade-to-robo-r1-r1.17128/ 12/27/2016 Added version 2 (all files with V2 in name). Version 2 incorporates the through slot...

I wanted a filament guide that would fit through the IKEA table with "rings" on both sides, and it had to be removable too. Since I couldn't find one online, I decided to make my own. Here's what you need to do: Drill a hole 35mm deep. To be...

**NOTE:** Also, I designed and uploaded a remix of dottom22's Bowden tube piece for his "Filament Enclosure Tap (1.75mm)": [Tweaked Bowden tap - Remix of Filament Enclosure Tap, 1.75mm, by dottom22](https://www.thingiverse.com/thing:4691036)...

Combine these components to craft a sleek and polished filament passage within the IKEA Lack enclosure, necessitating a precisely drilled hole measuring 22mm with a tolerance of ± 2mm.

----------------------------- This is a remix of the Enclosure Bushing Filament made by Raptor2063 January 30, 2021. It just add another pneumatic connector PC4-M10 thread, so you have connector inside and outside. --------------- Este es un...

This tiny thing guides your filament throug your top of the IKEA Lack enclosure. See attached F360-File for necessary cut-outs. Needs 2 M4x20mm truss-head screws. Print instructionsNone. ...Prints without support.

Model based on the filament guide for the new Prusa enclosure, designed to be used in the Ikea Lack enclosure, with the filament spool inside the box.The concept is very similar to that of the Prusa enclosure, with the filament spool inside the box,...

Mini filament guide I needed before I add a filament dry box on top of my LACK enclosure. I printed it with supports and drilled screw holes after printing since I kinda forgot to add them while creating, but it's super sturdy. I also added STEP file...

Mini filament guide I needed before I add a filament dry box on top of my LACK enclosure. I printed it with supports and drilled screw holes after printing since I kinda forgot to add them while creating, but it's super sturdy. I also added STEP file...

After few months of using, I decided that sometimes I want to use 3D printer as basic MK3S+ so i designed this filament guide to easily use enclosure as built before.I made few evolutions of my model. So, I decided to upload all of them. Best for use...

I initially downloaded the 'Ender 3 filament guide' by Holspeed for my Ender 3 and thought these modifications would help with management inside my enclosure. I have used them inside on the roof of my lack enclosure. You can check it out in the...

Located approximately 260mm from the front edge, this slot proved to be the perfect solution, allowing the filament to move freely left and right without any hindrance, resulting in a smooth flow every time. ...The end result is nothing short of amazing...

The rest of my enclosure setup is made from cardboard sheets glued together with packing foam "planks" on the bottom. The printer sits on this base, which absorbs vibrations and makes the printer much quieter. Vibration doesn't travel through...

A filament guide and spool enclosure for the Prusa i3 MK3 printer gets the filament spool off the top of the frame and provides a bit of humidity protection if you leave your filament loaded for a few days. It consists of three main assemblies. PTFE...

... the filament holder for the printer housing. ...Repeatedly, the rolls slipped off from their supporting structure. To resolve this issue, I modified the standard Prusa filament holder in ThinkerCad and it now functions seamlessly without any problems.

My version of the filament guide, exact fit for PC4M10 push fittings.Very smooth larger thread.I printed this in PETG with 0.15 Structural profile on MK4 InstructionsTop piecePlace it upside down in the slicerNo support neededBottom PiecePlace it...

Filament guide for Ikea platsa enclsure.Fits into a 16mm hole, a bit of glue to keep the parts together, makes for a really nice finish.Printet in PLA with 5% infill and a brim.