fidget spinner flash logo 3d models

... other passenger coaches, trains and freight wagons. I am still working on these and once happy with them I will release. End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515

Uno Double Outer Card Case: Just the same as double with a Uno logo. <b>Card Carrier 8unit:</b> This is for carrying and storing either 8 single decks or 4 double decks or any variation. I designed it with a line of magnets to allow for different...

The variants are as follows: There are 2 slot sizes (distance between the prongs of the clip): 0.25mm, for cardstock and photographic paper (1-sided or even 2-sided) 1.5mm, for thicker punchouts, plastic pieces or encapsulated cardstock (like the...

Overview.Wavetable is a customizable, 3D printed speaker stand for your desktop.Adjustable for height, width, tilt angle and more. The cantilevered design allows you to partially reuse the negative space below your speaker. Despite the smooth curves...

A great step to get used to OpenFigure3D models before going for the full articulated 3D printable figure, which you can find here.&nbsp;Available in various versions:Flex poseRegular, print all at once in a single colorMulti-part, allowing to print...

Also take a look at my other Designs!Changelog:Added a MMU version of the display coverAdded Beam with Prusa Printers logoSmall adjustments to the print filesAdded a color upgrade for the side partsAdded a symmetric version of the casingAdded an...

Raspberry Pi Zero and Pi Zero 2 Case Compatible with old &amp; newerPi Zero,Pi Zero 2 &amp;Pi Zero W (includes a camera ribbon slot) Snap fit design -no screws required. Heat sink hole for the 2W variation. "Coin slot" provided to prise lid open....

-Flat/open areas would be great spots to add a large logo or decal. -Another suggestion is red, white, orange, yellow, or other colors painted around the escape pods or the airlocks. My design philosophy was that important components would be...

Please keep in mind that this will reverse the logo engraving. We'll be removing the engraving in future panel orders and offering a sticker instead. ...You will also need to swap the positions of F5 and F6 (see manual) when assembling your enclosure,...

This only matters if you care if the Lego logo is oriented a certain way.Tip: If your screw options are limited and they're a little too long, you can add some washers under the mounting studs. This will add a small gap between the studs and the...

A little three color Raspberry Pi logo. Which is printed using the same techniques, but prints in a fraction of the time. So you can experiment with colors and print settings before committing to the larger case project. These striped sides...

Most plastics worldwide remain unrecycled, despite the recycling logo on them, and end up in landfills or our oceans, choking marine life and creating massive "garbage islands." These plastic waste islands are not dense enough to be traversed like...

There are also two versions of each walls that either have the shell logo on the wall, or not. The design is not textured. I'm open to making small changes if requested. This goes with my other building designs: Oddity Store (28mm):...

https://youtu.be/h0NZiODuCLI UPDATED 14/02/21 150mm VERSION ADDED UPDATED 22/12/20 100mm VERSION ADDED Lithophane Stand for Ikea LEDBERG Spotlight NOW INCLUDED LOGO FREE BASE The stand Fits Lithophane's made from...

The best print configuration for the parts I found were with the ducts facing up, with supports only on the flaps with the screw holes, and for the case, I thought it was better to print it with the "T" logo facing the table, as shown in the images....

It's really up to you how many tall or small trunks you want to print. • The Bonsai (mini) box can hold 40-56 leaves, stacks of 4 trunks or 3 tall trunks per slot. The box is 115x115x63 mm • The Cherry Box can hold 20-24 leaves, and stacks of 4...

You will need to rotate one of the displays therefore to the left and the other one to the right with “hyperpixel4-rotate left” or “hyperpixel4-rotate right”.My USB-A cable sides went in easy into the ports as connection to the printers, but this may...

I've learned from creating the many pictograms in my 49 Room Signs Like "The Office" logo (https://www.thingiverse.com/thing:3321080) that precision crafting is an important part of designing 3D models whenever the models have areas that are only 1...

... near the screw holes to bond them to the brace body. Want a different logo or wording? ...Feel free to drop a comment or message about custom inserts, or maybe I will post sketch dimensions for the Upper and Lower Inserts if there is much interest.

I've included a body and faceplate without markings or logos, which you can print, drill, and mark to suit your parts/needs. I've also shared an archive of the raw design files, originally created in Inventor but you should be able to import it in...

Before installing the thermocouple and the heat cartridge determine which will be the right and left side hot end.  The heat blocks will be installed with the Slice engineering logo facing on the outward sides of the extruder.  This is to...

If higher gear ratios are needed a 2nd set of gears will be needed, this design uses only one planetary gear set.\n\n \n \n Update Log\n10/22/2016 Added a 1:9.8 gear ratio, 3" (77.4mm) gearbox, which pushes the limit of torque possible with thin PLA...

(Suggest u measure and push it around in sauce to fit your fittings rather than try to match mine as i cant even find teh switch i used) What can/should be improved: Make front grill attach w/o evil glue Separate pi4 clean back inputs using risers...

I also removed the BX logo and adjusted the edges of the outlet to make it more ASA filament friendly. Optional Upgrades ----------------- The Claw Fang Duct: https://www.thingiverse.com/thing:5202213. More Ender 3 models at...

A little three color Raspberry Pi logo. Which is printed using the same techniques, but prints in a fraction of the time. So you can experiment with colors and print settings before committing to the larger case project. These striped sides have...

My final changes were minor, and purely cosmetic: I added an additional curve to the rear section of the base, and picked a nice font to slap a recessed "GT3" logo on the (now wider) pedestal part of the stand. The finishing touch was to add 4...

My “logo” will be concealed by the pi once it is seated.Functional: Case allows for access to the IO pins from both sides, ribbon connections, SD card, as well as the power button and LED. You will probably need something to poke the power button in...

I have included the SVG files I used in making of for the Flynn's sign as it's hard to get the logo correct, and the font is not freely available. This design maxes out my Rep2's build area on the X so you may need to rescale everything to print it...

2 more mount holes.As reference I used https://www.thingiverse.com/thing:4060718 (CR-10 V2 X carriage model)Directdrive-BMG-V6_Mount-Back-CR10-v2.pngDirectdrive-BMG-V6_Mount-Back-CR10-v2.stepDirectdrive-BMG-V6_Mount-Back-CR10-v2.stl2020-10-01Remix by...

If you’re looking for a custom-logo version, reach out. Note that you can make a little electrical tape “handle” to make it easier to pull out. The glue between the circuit board and battery case for an AudioMoth can vary in size, and for...