fidget 3d model

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

If you decrease the size of the model, you will end up with less than 2 layers which might decrease the integrity of the maze. You should be OK increasing the size, but the maze walls may not fuse in the middle using 2 layers. You'll need to...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

 You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing.You will need to do some tweaking to keep the led matrix against the grid.  This can be...

... self sustaining for long periods. All ground piping, cabling and the Large Gas collection cansiters would be covered in Dirt once operational for Sun / wind shielding. Note the Space Suit man was inserted for size, got it from the NASA models site

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

If you have a tuned in printer, bump the speeds up a little for a dramatic improvement, (make sure wall thickness is a multiplier of your nozzle thickness - The parameters are important and there are a lot of dependencies, Make sure you have done the...

print the uppers in a 100% infill! Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

I have re-modeled them a bit and now there are only a few strings. None if you print them with a 0.12 layer height. Filament Dry Box Set (Updated 3/11/2021) This set of prints are designed for use with the following items to create a very slim...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

The airflow is higher than stock and the Draken due to its duct design but it has more channels.The main point of developing the Gripen next to the Draken is for printing models that need less but more controlled cooling, meaning it cools from all...

Just copy your gcode to the same folder as the exe, run it, select the options you want and when you've confirmed your choice it will automatically open the first gcode in the same folder and write the temperature changes for you.Extract...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

... this design, but don't want the silly text on the knife strip? Check out the modular version! Modular Wall-Mounted Magnetic Knife Strip

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

The COMPLETE Order of the Labyrinth bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The strong Minocs of the Order of the Labyrinth are the descendants of Tesevros the Wise,...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...