ferro 3d

I'm still using the 8bit version of Marlin given my driver board, but have had good luck with Klipper 3D - an excellent way to get new life out of your Arduino-based driver board assuming you have a Raspberry Pi hooked up to it. Regardless, taking a...

A steel axle would be overkill but a 3D printed one is replaced in minutes and you can use anything with a diameter of 5mm as an axle.Tighter construction -&gt; less wiggling of the parts. Feels sturdy.</li><li><strong>No need for support</strong> in...

Violence is never more than a heartbeat away.Shelter yourself! Deliver your cargo!Stay in the fight!Small painted-on supports are required for the following (Support Enforcers Only):Space-Port-OPEN-Module-PT1-V1Space-Port-OPEN-B-Module-PT2-V1...

See the bundled "Using OpenSCAD customizer" PDF for more details.Recycling symbol offset: An extra thickening (positive offset) or thinning (negative offset) of all the symbol, to aid in 3D printing. Usually you won't need to add any value, unless...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

You can cut the circle that's sandwich between the two 3D printed pieces with good scissors. The holes for the crews and the tube are harder to make. Be careful, this mesh is sharp and you can get cut. I'M SERIOUS. I managed to make the screw holes...

Dragon and Mosquito use the same length of PTFE tube which is why they share jig.BOM - Bill of MaterialsI buy most of my 3D printer parts from quality stores on AliExpress. Shipping takes a while from China but quality is excellent and the prices are...

See “Large Binder Clip Tentacle Monster” below in connectors.Tentacle Rail Clip BaseThis Tentacle System base includes a clip that attaches to the T-Slots in the aluminum extrusions used in Prusa and other 3D printers. Used in combination with the...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

My bot came with 410 mm Y rods, which is reflected in the Blender file, but this design should work on older printers with shorter rods (the original i3 had 330-335 mm Y rods). The .blend file depends on my standard parts/materials library, which can...

I did not try to 3d print everything in plastic if metal or wood made more sense and was faster/stronger/easier and not cost prohibitive.  3D Printing is mostly used for the connections and exact positioning of tubing.Everything here is my own design...

What to print: Print these files: icarus-1.2.1-for-sherpa-mini-r1-normal.stl sherpa-mini-r1-dragon-mount-1.1.stl icarus-dial-holder-1.0.stl icarus-belt-peg-1.2.stl icarus-fan-duct-1.3.1.stl...

Potřebné vybaveníNotebook nebo tablet, programy Tinkercad a PrusaSlicer, 3D tiskárna.Nepovinné - krabička čtvercových rozměrů, tvrdý papír, pravítko, tužka a nůžky (viz postup).9. Potřebné soubory a dokumenty (seznam...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

Use with Right MMU2 Mount Z-Axis Top.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired hardware:Aluminum u-channel24V...

This is a followup to: Lack Attack#3: Koppla the Lack: https://www.prusaprinters.org/prints/15919-lack-attack-3-koppla-the-lack-aka-power-the-lack-s without further adieu.... Attack 4: ENCLOSE THE LACK Its been a while since my last update, mostly as...

These strips are bright enough I didn't notice only one was on. View from Octoprint Control tab during the first layer of my first print after installing. Print instructionsCategory: 3D Printer Accessories Summary Prusa i3 MK3 PiCam v2 X-Axis Motor...

(it is already in the settings in the .3mf files)Assembly:Print all three parts (hull, treads, and gun.)Superglue the treads to the hull.Place the gun on the roof.Superglue works best for gluing it together.It will scale easily if you want a larger...

With external markings and without.Stand up your Space Port before it's too late!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under...

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

I'm not telling you how to 3D print parts and clean it. You know it. BOM: '1. RPi 3A+ / Zero W /Zero W2 (and similar clones that have the same outline as Zero), microSD card, '2. Raspberry PICO working as keyboard martix USB HID device...

Just to make it easier finding it all in one place.No support required.Diesel Generator you will need to superglue the bottom frame (very simple)Designed on...

Worlds are waiting.Equip yourself today, citizen!Space Port - https://www.printables.com/model/205432-space-port-terrain&nbsp;Starship Cargo Pod - https://www.printables.com/model/224797-starship-cargo-pod&nbsp;Starship Transfer Tug -...

His diagrams and commentary on escapement efficiency were excellent, however.&nbsp;I only discovered this write up on escapement design after I'd finished, but it would also be a useful head start for anyone interested -...

Use thread lock to ensure these will not accidentally come loose.A 36mm diameter propeller should run freely inside the rudder at all rudder angles.Mount the rudder support to the hull using M3x6mm screws.Then put another M3x6 screw to secure the...

Or, see the retainer tool below for a 3D printed solution to this potential problem  Retainer ToolHave you been a victim of the Domino Effect causing all of your lights to end up on the ground? Are you worried you could be? Well fear no more! The...

The SolidWorks Certified Software Application (CSWA) exam is a comprehensive assessment of an individual's skills and knowledge in using SolidWorks, a powerful 3D computer-aided design (CAD) software. This exam is designed to evaluate the ability of...

Remove the z-axis tops and replace with this light bar mount.&nbsp;Print instructionsRecommended Print Settings:Layer Height: 0.20mmInfill: 15% GyroidSupports: Build plate onlyOpen 3MF files in PrusaSlicer for preconfigured settingsRequired...