female mast 3d models

The holders are designed specifically for Catenary mast, created using barspin technology from thingiverse.com. These holders perfectly match LGB sleepers and the second model is tailored to fit my custom-made plexiglass sleepers that are 13mm wide.

This is a remix and modification of a previously submitted kit by Sean Franklin - https://www.thingiverse.com/thing:5571629 I used some of his design - the base, platform and the ladder as the basis - the signal platforms are inspired by current...

Now the antenna is mountable to the expandable mast of the old yagi-antenna (OD 16mm). The actual sat dish has an rod 10mm with a thread M8. You have to insert a nut M8 into the holder to screw on the antenna. The main advantage is to bring...

... together using it as a bridge. Secure the connection between the parts and the rod by applying 15-minute epoxy to the joint. Next, revisit the spreader component and reattach it in each of the mast halves with an additional dose of 15-minute epoxy.

Works with this GPS: 3DR uBlox GPS with Compass Kit https://store.3drobotics.com/products/3dr-gps-ublox-with-compass PIXHAWK GPS MAST F450 Very strong foldable I have used a brass screw for the GPS socket (non metallic) (4 x 5/8) And Zinc Plated...

A triangle shaped mast and sail. It is made entierly out wood with a white cloth as sail. The wood is a UV mapped texture and the cloth is a material. All the colors and textures can easily be changed. The model is made out of multiple parts and can...

Playmobil Pirate Ship Rope Ladder/ Mast Rigging. Modelled for the Playmobil 5950 Skull And Bones Pirate Ship, but should work with a number of other Playmobil ships. The rope ladder is approximately 13 inches long. To print a Left or Right hand...

 The system has four components including a motor box that attaches to the MastWerks mast crank fitting, an electronics box that holds the circuitry required to control rotation, a circuit board and a battery box.  The boxes may be attached to the...

Print Settings: Printer: Prusa i3 RW mod Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: Refer to notes for specific instructions Notes: Print the mast and support with 100% infill, then print the second piece with 20%...

See pictures.You have to print the following parts:1x main bracket, 2x profile connector, 1x holder_for_stütze, 1x mast clamp holder, 2x connector support, 8x solar panel clamp holder_Teil1, 8x solar panel clamp holder_Teil2.The parts should be...

I'm using this yarn tension mast with the 3d-printed knitting machine. It can be used with any knitting machine. I've tested it with the Addi knitting machine and it really helps to get consistent tension on the yarn. ... Also, would come in handy...

GONAM Fire Skull Ship Sails into Battle as Proxy in Man-O-War Games Created by Nat Hunt, Found at https://www.thingiverse.com/thing:3866000 The ship's fearless skull emblem on the front was remixed from a heroic scale 28mm skull design, accessible...

Works with this GPS:\n3DR uBlox GPS with Compass Kit \nhttps://store.3drobotics.com/products/3dr-gps-ublox-with-compass\n PIXHAWK GPS MAST F450 \nVery strong and durable\nCompact foldable design\nI've secured the GPS socket with a non-metallic brass...

This thing is a bracket to fix an iPad mini on the back of the mast of an Archambault Surprise 25. It can be used with an aiShell from Andres Industries, which I recommend (1st picture). Alternatively you find enclosed a case for an iPad mini 2,...

built to go up to 250 meters of height, 12 meters of lenght ( single mast configuration) and lifts 2500 Kg of load .it has 2 electric motors, 2 electric brakes and 1 mechanical anti fall brake plus a manual lowering system in case of electric current...

I love the design of Jacks Traktor Sprinkler, however I had a few of issues with the central mast or pinion of the mechanism. The printed pinions always broke right at the upper thread, just a tiny bit of force on the spray-arm and it snapped right...

I purchased a J-pole antenna from a fellow ham radio enthusiast, but it lacked a sturdy mast mount suitable for my condo environment. To secure the antenna, I designed a custom mount using a bucket of cement and a 1/2" PVC pipe 'mast'. Tonymtsai's...

I'm building a guy wire plate for my 10m amateur radio antenna mast. There are plenty of forces at play here, so I've intentionally over-engineered it. The result is a palm-sized equalizer plate that's as tough as rock. This is the first iteration,...

... The clamp section, which securely holds the pipe in place, is sized to fit standard 1.25-inch outside-diameter (O.D.) pipes commonly used for US television antenna masts. I chose #6 sheet metal screws that are 1.5 inches long for this application.

This is a set of 3d models for 3d printing the SS United States Main Mast as a decorative sculpture. One piece Low Rez STL file is available here. You can download a higher-rez version for free from my site: https://www.endtas.com <-- visit...

Well, as stated, my I broke the mast/actuator section on my dropper post whilst trying to remove it to service the post(it had basically siezud up in there, and took a lot of force to remove). They also seem to be unobtainium if you want to buy a...

( I bought mine here: https://armysurpluswarehouse.com/camo-netting-poles-fiberglass-4-for-11-95/ ) Many ham/amateur radio operators use these poles to create antenna masts, and this tripod can help with stability and set up. UPDATE: I've included...

... with the original parts. Users may choose to retain the original upper cap while incorporating the modified lower cap and mast. Additional components will be added to this project over time. ... Print Settings: Printer: Wanhao i3 Plus Infill: 20%

This 3D model accurately depicts the Emley Moor television mast situated in Huddersfield, West Yorkshire. Characterized by a tapered structure made of reinforced concrete, it stands as the tallest freestanding edifice within the United Kingdom,...

I created a portable fishing pole mast support to keep the first element standing on its own without needing to tie it to something or carry a tripod with me. To set it up, simply place the big ring on top of the thickest pole element and secure...

Windsurfing Gear and Boats for Water Sports and Fun Activities.Windsurfing is a Modern Ocean Sport that Combines Sailing and Surfing Elements.It Uses Small, Lightweight, Easy-to-Maneuver Boats for Riding Ocean Waves.Everything You Need for...

We wanted to make a monoblock hydrofoil, where the front wing, fuselage, and rear wing were one unit and that unit fits into the mast. That is what this is. We wanted to ensure that newcomers to the sport do not have to worry about all the different...

This is the link to the original design: https://www.printables.com/model/136656-guy-wire-system-for-spiderbeam-mast-with-rope-tens this is the mast (fishing rod) that I bought:...

MAST hull Reniforcement

A simple female-to-female connector for Brio (R) train tracks