female header 3d model

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft:              YesSupports:    NoI've had the best luck printing these using a single-layer raft, with the part oriented...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

https://www.youtube.com/watch?v=Nn9B46IjsVU ______________________________________________________ ENGLISH ______________________________________________________ Only tested on T12-X, but can work on equivalent models with boxes of the same...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

and using less material) The idea is to print the markers in a different colour using the "Filament change" script (under Cura, M600 gcode, if supporter on your printer); you may also use the standard rotor-cover.stl if not interested by this version...

This is a multimaterial model. I don't have a multi material printer but learned that you can create a multi material print pretty easily without special hardware (as long as the multi material part does not span over to may layers - otherwise it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aera under...

The assembly is tailored for the older model C8, CeleStar Deluxe with the double fork equatorial mount and an under-rail for weights, dating back to c1998. Materials List • The three C8 Camera Mount Assembly prints o C8 Front Bracket o ...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

See Latest Updates Below ----------------------------------- * The latest model now appears at the top due to rearranged pictures. I wanted a unique look for my 4x Santa figure, if that's feasible... Took various elements from multiple 4x...

Your input is welcome!\n\nPrint Settings\nPrinter: \n Anet A8\n \n Rafts: \n No\n \n Supports: \n Yes\n \n Resolution: \n 0.2\n \n Infill: \n 100\n \n Notes: \n I used Cura 2.4 to print this.\nCheck the pictures to see how you should lay the model...

I design a Electronic Bay Cover with LED Light Just a little favour>>>Less then 10% of downloaded Models get a like.→ If you like the design, it will be nice if you click on the like button and maybe share your print.   Its a heavy redesign of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Tools Hex wrench 2mm and Mmm...

Now, everything will just fit without removing the box insert.ModelQtyDescriptionquacks-chip-box.stl2Boxes for Red, Green, Blue, and Yellow ingredientsquacks-chip-lid.stl2Lids for those boxesquacks-misc-box.stl1Box for the miscellaneous ingredients...

Sincethis design is compatible with a whole variety of lampshades, be aware that somelampshades will have to be scaled down or up to fit the base's default settings. Base- Layer height: up to 0.3mm is fine, there's little detail on the Z-axis-...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

For me it wasn't a problem, but I've added a bit of chamfer to the bottom for a bit of extra movement. If you manage to make a square 16x16mm glass then I've included a 16x16 model without the bottom portion that should not limit the camera...

(This is all also in the README)I commissioned prints for these models using PLA with 40% infill and they work like a charm.- You will need to print the Rear Panel if you want to use the parts in the MOBO and GPU folders.- The PSU folder needs to be...