fear from inside out 3d models

additional data from www.openstreetmap.org (http://www.openstreetmap.org/) served as primary reference in developing the city's buildings, streets. points/verts: 1582324. polycogs : 1037993 available formats include - .c4d (native file format of...

All versions require some supports, which should come off easily (and in the case of the split version, they make removal from the print bed simpler if you don't have a removable bed). An overview video showcasing how I created this design and...

From a print height of more than 1.5 mm, I only overprinted the outer circle with gray PLA. It looks a little better in the dark because you can see the ring less. I warmed up the butterfly on the wings and bent it a bit, this creates a 3D effect. ...

I printed on an Ender 3 v2 with cheap filament from Micro Center so it doesn't require high end stuff, but it does require a fairly well calibrated printer to ensure everything is the right size so make sure your steps/mm are calibrated for X, Y, Z,...

So I decided to create it from scratch.This modular storage system was optimized for printing in vase/spiral mode using 0.8mm or bigger nozzles. Printing in spiral mode was one of the main requirements for modeling due to its lower filament...

This sensor is made for Anet A8, AM8 and Tatara (but the last two aren't published yet) Bill of materials 1x resistor 220ohm 1x resistor 10kohm 1x LIRED3B 940nm 1x LIRT3B 940nm 1x nail 3mm thickness 70mm lenght 2x neodymium magnet 5x5x5 (cube) 1x...

I would like to see someone do a full button up shirt and maybe even have the gears mesh from one shirt hole to the next!A good remix would be a stem off of the outer gear for a lavalier (lapel) microphone. This would be cool for a science or...

After drying remove from display stand. 10. Glue the bottom rib joints together. Lamp Body The Lamp Housing is a close fit. Depending on the printer, it may need some sanding to allow it to be pressed into the bottom of the Lantern Body. It...

Bei kleineren Werten reagiert die Lichtschranke schneller, kann aber auch dauernd auslösen.Zudem kann, an Stelle der Reflexionslichtschranke, auch ein  normaler Schalter verwendet werden, siehe letztes Bild oben. 1x Widerstand /...

I removed 2 links from the last set. Assemble with additional filament. The idler axle can be rotated and glued to maintain proper tension at this point.Install Mantlet into turret with two pins. I tapered one end to help locate them into the holes...

You will need: x3 20x6x2 neodymium magnet (x1 is included with the printer, the other two are optional) x1 10x6x2 neodymium magnet (x1 is included with the printer) x1 7mm metallic ball (x1 is included with the printer) x7 M6/M8/M10 fittings (you...

An alternative Base for the Antenna from the Nachmund Fronteris set. If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link: Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet...

Here's an excerpt explaining each part: ```python # Set up SVG.js to render shapes based on the script's conditions // Generate shape arrays based on mathematical operations with random numbers ``` ### Shapes Generation Logic ```javascript // Shape...

It is also interesting to choose LEDs that have the cold and warm white chip independent from the RGB, in this way they are used to illuminate the room like a traditional lamp This is the model I have:...

 The adhesive mount’s socket is smaller than the base’s ball, but the socket’s locking ring holds it all firmly together anyway.I spliced the magnetic charging cable into this charger – but if you didn’t want to cut the cables, you could...

From modern operating rooms and advanced medical equipment to welcoming patient rooms and bustling nursing stations, each model is crafted with unparalleled precision and detail. Perfect for game development, virtual training simulations, and...

In the original design the arm of the crane did hang down a bit, and I was also afraid that over time the PLA will break from the stress. So I designed the whole light with a counterweight which depends on the weight of the arm and its length. #...

Since this is so much changed from the origional one, and none of the origional parts will fit this variant, I figure it is best that it is its own thing. This will print all types of 3.00mm fillament, including flexible fillaments, filled (woodfill...

Take care when choosing the colors. Design:I took the .svg files from Wikimedia (link below) scaled them to 170 mm using inkscape (link below). The rescaled version is then loaded to Fusion360, where the base profile is extruded in negative direction...

All parts were rebuilt from scratch in Fusion 360. Apologies in advance if any of the items below are included in another remix - I have not spotted them. In this remix I have: 1. Created a sturdy 3 point fix solution for the base to the mounting...

NOTES: While I don't recommend PLA for this purpose, (It's exposed to UV and water after all) I chose to use PETG and protect the conduit from UV by wrapping it in duct tape. It's working well so far, but we'll see how it's going after a couple of...

Note: live picture taken from the 6" version. Now lets check the claims: 1) super light yet crazily stiff This 7" frame does weight around 60-70g in total (depending on used mounts). This inclused the GoPro as well as the GPS mount. It uses 6mm...

To ensure the whole thing didn't just fall apart I drilled holes in the aluminum and inserted the aluminum caps from some blind rivets I had lying around. Anything with a 3mm diameter should work such as some small nails or machine screws but the...

Signal dimensions are taken from the book Model Railway by B.V.Barkovskov et. al. Published - Moscow 1989 - ISBN 5-277-00181-6 p78-79. Additional documents with dimensions were found at the Russian scaletrainsclub.com forum. A very comprehensive...

Included are the item numbers from Radio Shack for the electrical parts if you choose that route. Rubric and Assessment At the end of this activity, the students should have a completed compound gear train that can lift the elevator. I have...

In the case of reverse it is right on top.Mix #1Mix #2ReverseStep 11: Go, Go, GoPlug in a 3s 450mah batter from fingertech website. ...Drive it and have fun.</p><p><strong>Step 12: (1/4 of the time this is not applicable)</strong></p><p>If motor goes...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

Some models are remixes but mainly are made from scratch. affiliated Tools used to build the motion simulator: IWS-2820M Crimp Tool (good one): https://es.aliexpress.com/item/4000073000826.html Small usefull wire stripper:...

5 - In general for all my models, when removing parts from the printer bed, it's a VERY good idea to place left/right parts into separate containers to help with the assembly process. Sometimes the difference between the left and right parts is...