fanuc arc mate 100i 3d models

The tolerances have all been cut in half with the scaling down to 50% so parts that mate will fit tighter. I think this has a good chance at being faster to print and build though.  It may need a little more effort however so don't print if you are...

Note,don't apply any lube to the ribs in the inside ring of the Lens, this is not a thread, it is a light scattering baffle.Thread the Lens part into the Middle to distribute lube like you did with the Body and Middle, and leave them separated when...

Then, place the eyelids into the lenses, making sure they make contact with the glue you just pushed out from the lenses sides:If the eyelids don't properly mate with the lenses:you'll have to push them up a bit. To do so apply a big drop of your...

He had been Samira’s First Mate back in their navy days and had conspired with her to keep the damaged Bloodwell hidden, partly because he too wanted to free himself from the imperial mandate. In his new mutated form, Sully is much more than twice...

Trim each extruder-hotend component to the following lengths.Hot-End 200mmThermistor 280mmStepper motor 180mm5015 fan 240mm4010 fan 170mmPinda probe 180mmFilament Runout 70mmWiring the loom to the MUTANT Static plate MUTANT PIN Configuration for...

Hot-End 200mm Thermistor 280mm Stepper motor 180mm 5015 fan 240mm 4010 fan 170mm Pinda probe 180mm Filament Runout 70mm Wiring the loom to the MUTANT Static plate MUTANT PIN Configuration for Prusa MK3S (4 wire Pinda) A Red Heater B Red Heater C...

It is printed without support, flat on the print bed.Assembling instructionsBefore gluing anything, dry-fit the pieces and make sure they fit properly, and lightly sand and clean all contact areas.When gluing, use tape and small clamps to fix the...

It's still experimental as of writing this, but hopefully it'll be working fine soon (if it isn't already!).Applied the suggestion of user Dave, and added an option for arcing scale lines.Added an offset parameter for primary and secondary scale...

 The loops form naturally on retraction, and when being pulled through it the filament goes in a  wide arc with very low friction. I prefer this buffer but I understand it is asking a lot of folks who already have the Prusa buffer printed. In that...

I went back up-stairs and from the open window watched Brett walking up the street to the big limousine drawn up to the curb under the arc-light. She got in and it started off. I turned around. On the table was an empty glass and a glass half-full of...

Type: Binary star surrounded by a reflection nebula. Distance to the Sun: 7500 ly. Orbital period: 5h 36 min Dimensions: ~1 ly long, ~0.46 ly wide Model scale: 1:2.028x1016 (44cm high) 1:4.056x1016 (22cm) 1:1.2168x1017 (8cm) References Eta Carinae...

The printer is working well and has been printing parts for its Kossel XL stable mate. Update 20-12-16 So after switching the max PWM back to 255 for the hot end heater I was running into a problem of not enough power on the 5A connector (for...

Icarus 2 has been released which is the current version and it has a number of improvements:View Icarus 2 hereUpdate December 21, 2021: Icarus now supports the new Orbiter 2.0 extruder. If you're already using Icarus with Orbiter 1.5 or Sherpa...

Icarus 2 has been released which is the current version and it has a number of improvements:View Icarus 2 hereUpdate December 21, 2021: Icarus now supports the new Orbiter 2.0 extruder. If you're already using Icarus with Orbiter 1.5 or Sherpa...

Icarus 2 has been released which is the current version and it has a number of improvements:View Icarus 2 hereUpdate December 21, 2021: Icarus now supports the new Orbiter 2.0 extruder. If you're already using Icarus with Orbiter 1.5 or Sherpa...