fanatec pedals 3d models

I required a mounting solution for my Fanatec V3s pedals on the Playseat Challenge, so I devised this design. I manufactured this in PLA, yet you could opt for PETG for increased strength. There are two variants: one is tailored for M8 bolts since...

I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting and...

The Fanatec Elite Pedals boast precise measurements, ensuring accurate readings for an enhanced gaming experience.

These are some pedal plates I designed for my Fanatec CSL pedals with Load cell. I decided to invert my pedals and was sick of the stock pedal design. These pedals are based on simworx pedal plates and are designed for heel-toe technique in mind. ...

Fanatec CSL Pedals Pedal Plate Plug and Play with Fanatec Logo and F1 Logo.Multicolor printed on Bambu X1C

I liked the original design, but it didn't fit my CSL pedals that came with the Fanatec DD Pro. I managed to use the original part for the front position (closest to the chair) and I remixed the design for the rear position, so the pedals can be...

# Universal Playseat Challenge Fanatec Pedals Mounts After breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. This universal mount allows you to affix both Fanatec...

Universal Playseat Challenge Fanatec Pedals MountsAfter breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. ...This universal mount allows you to affix both Fanatec V3...

This set can help to enlarge back area of CSL pedals so you can push it onto something in case of sliding pedals.BOM:2 x DIN912 M4x602 x DIN934 M4WARNING: Do not overtighten screw, there is a danger of bending pedals metal frame.

Rumble motor mount for Fanatec CSL pedals. ...More infohttps://github.com/elenhinan/ESPTurismo

A versatile accessory to attach a TT25 PUCK bass shaker directly onto the brake pedal of your Fanatec ClubSport V3 pedals. ...For more information, check out this instructional video: https://youtu.be/al3gEAN6RiI

Based on a video posted by amstudio at https://www.youtube.com/watch?v=8aLqqcEaUVk&index=4&list=PLW_mVHJcIJmFL9AQvqOPWl9R9LVWlCZAX&t=399s, I created the rumble motor holder for the Fanatec CSL elite pedals with load cell. ...The design draws inspiration...

https://youtu.be/9lxu1R-dmdc ressorts utilsés: https://www.conrad.fr/p/5-ressorts-x-l-225-mm-x-815-mm-889249 https://www.conrad.fr/p/5-ressorts-x-l-27-mm-x-885-mm-889247

When I made this design the LoadCell option was not available for the Fanatec CSL Pedals. Anyway for anybody who likes DIY project it still can be an option :) Parts you will need: - load cell (50kg in my case) - 608 bearing (22mm x 7mm) - 1...

i was doing service on my Fanatec Clubsport V3 pedals and noticed my hydraulic damper was missing a bolt and a shim spacer thing. the other side was still there so i made one. the original bolt was a M4x6mm bolt. i had M4x8mm bolts so its made for a...

This is for vibration motors mount that fits to the Fanatec Clubsport v2 pedals. It will also fit to v1 and probably v3. The original vibration motor was removed. You can use it for all three pedals. You will need longer screws to mount the mount. ... ...

This is a board holder and hall sensor holder for my Fanatec Clubsport V1 Pedals using Leo Bodnar Electronics. The hall sensor simply fits into the rectangular gap and is held in place with some hot glue. I put the top of the sensor flush to the...

If you're like me and somehow lost the little spacers inbetween the Hall Effect Sensor and the pedal on the throttle or clutch pedal then you're in business! These are to scale models of them so you can print some. Note that because of it's size,...

Adjusting the Brake Preload on Your Fanatec Clubsport Pedals V3 Just Got a Whole Lot Easier The perfect brake pressure can be a game-changer for racing enthusiasts. Getting it just right requires precision and patience, but with the right tool in...

<p>Holes a 4mm wide<br>You will need a 4mm bolt and nuts.&nbsp;<br>Bolt should be 20mm long as the pieces when assembled are 15mm thick.</p><p>Should look amazing if resin printed.</p><p>&nbsp;</p><p>Enjoy!!</p>

No need to take the pedals plate.Don't go crazy tightening the nuts, just make sure the mount is secure on the pedals and cannot move.Put the pedals to the Playseat pedals mounts.Tighten zip ties by dragging back and forth.Cut down the excess using...

Replacement flexible grippy pedal cover for Fanatec CSL pedals. Print in TPU. The model is sized for an extremely snug fit, and you will have difficulty putting it on. Use a screwdriver or trim tool on the back, to pull the TPU lip over the...

I designed custom pedals for my Fanatec CSR pedals since I didn't want to buy the brackets sold by Fanatec. The only problem with the design is that I miscalculated the opening where part of the pedal assembly will slide into by 4mm on the brake...

This protective cap secures the rumble motors of the Club Sport Pedals when mounting them upwards requires it.

(TPU for sound damper required) You need 4x M6 60mm Bolts and 4x M6 Nuts and a set of RC Car Damper with 140mm length like these: https://aliexpress.com/item/32603488386.html If you want an even stiffer gas pedal you can also order these (2.0mm +...

Recently purchased the Fanatec CSL DD Wheel & CSL Pedals combo intending to mount on my Playseat Challenge. The wheelbase mounted fine, but the pedals had no good way to mount rigidly other than the large velcro strap that comes with the Playseat. ...

Remixed "Tiltons Peldals Pads Universal Remix for Fanatec, Logitech and Thrustmaster by P3sc4" (https://www.thingiverse.com/thing:3687333) in Blender incorporating the following design changes: - Center to Center vertical bore hole distance 19 mm -...

Print 4 x Mounts Add 4 x M6x20 Hex screw 4 x M6 Locking Nut 8 x 6,4mm washer 8 x Cable Tie 4,8mm

Installation Guide: https://github.com/team-sillex/simracing_mods/tree/main/ClubSport%20Pedals%20V3%20Clutch%20delete

If you own Fanatec ClubSport Pedals V1, V2, or V3 and want to boost realism by reversing them, which is essentially turning them upside down, then you'll find this custom pad setup extremely useful. I decided to design and print some replacement...