fanatec csw 3d models

Designed to go in between **SimLabs Pedal Plate** and **Fanatec V3 Pedals**. May also fit other pedal plates. ...To check yourself on your pedal plate: - distance between the two holes for mounting is **35.8mm** (holes outer edge to outer edge) -...

Fanatec CSL Elite Pedals Motor Rumble Mount for "ShakeIt" motor software. I utilized an old PS2 and Xbox gamepad motor for the project. To assemble the rumble mount, you'll need some zip ties and M3 bolts and nuts to secure the cap. If you have...

A bracket mount designed to securely hold two knobs and a headset in place, utilizing the standard hardware components that come with the Fanatec Shifter. The pins on which the knobs rest may require adhesive tape to minimize vibrations during use.

This is a magnetic shifter mod for Fanatec F1 steering wheel. Gives it a much nicer positive snap when changing gears. Best to print it in the original orientation with supports under the small part for a stronger part. Make sure the magnet...

... it for 150% extrusion for strength; this profile is also uploaded. Rescaled "Fanatec Clubsport v2 Tilton Pedals by 3lfk1ng" in Blender for my V1 ClubSport pedals. The center to center bolt dimension is 19mm. ...The total pedal length is 11.4cm.

i was doing service on my Fanatec Clubsport V3 pedals and noticed my hydraulic damper was missing a bolt and a shim spacer thing. the other side was still there so i made one. the original bolt was a M4x6mm bolt. i had M4x8mm bolts so its made for a...

This is a mounting bracket to hold a Fanatec Emergency Stop Button to an 8020 style aluminum extrusion with dimensions of 40mm x 80mm and two 8mm slots. It holds the E-Stop button at a 15° angle from vertical and includes a cutout for the wire. ...

This is as a Mige Motor Mount for the Fanatec Clubsport Static Shifter paddles. V1. this is a rough first design but works well enough. Spacers to print are included at 5mm increments to adjust the paddles. This mount assumes you are using a motor...

Hello,this is a phone holder I created to display a little dashboard on my Fanatec CSL DD wheelbase.It has seperated spacers, in case your screws are too long, as mine were.Spacers are 10mm long and a bit wider on one end to support the holder a bit...

A small print to avoid breaking usb c connector on Fanatec GT DD pro. Useful when you change USB cable often, from PC, to PS5, to XBox … USB connector fit without resistance, but avoid sides movements. Use a long M5 screw, at least...

Used to mount "Podium Kill Switch" the fanatec power button for Podium DD1/DD2 direct drive sim racing wheels. ... https://fanatec.com/us-en/accessories/wheel-base-accessories/podium-kill-switch This mounts one side of the e-stop flush with the side of...

If yours is too tight a fit, it may be down to Fanatec's hole drilling QC, in which case just sand down the print a little. ... Printed on: ender 3 v2 filament: PLA (others should be fine, that's just what I use) Layer height: 0.16mm (others should...

These are spacers designed to fit behind the Throttle or Clutch pedal of the Fanatec CSL Elite pedals. The hard rubber part which comes with the pedals gives 20 degrees of travel. The fit might be tight or loose depending on printer tolerances so you...

I designed these slim one-part magnetic shifters for the clubsport universal hub v1 (v2 already comes with the fanatec magnetic shifter). No need to de-assamble the shifter arms since the shifters of the universal hub are metal parts and these...

I needed a customized mount for my Fanatec CSL Elite wheel base, which led me to design the model in TinkerCad. The resulting phone design was created specifically to hold my smartphone, which I use to track telemetry data during sim racing sessions....

hello no luck for me after the csp v1 it was the turn of the csp v2 to have problems with the sensors or the board, even in real fanatec we look to the west, some don't have a problem... I got fed up and I suggest switching to 10khom...

3 toggle switches to start/ stop my smartswitches 1 Button to start Fanatec DD1 (connected to RJ45 2 Buttons and 1 Encoder as Controller Arduino Micro 1 Flag/ Gearlight WS2812 8x8 64 LED Matrix at Arduino Micro with grey plexiglas 3mm in front 1 6...

I have pretty high table, so with table clamp from fanatec my wheel was at weird angle, so I designed my 0° table clamp, so I can sit low while playing F1. I printed it laying on side so it doesn´t need any supports. I´ll see if it needs any more...

These inserts are specifically designed for the Fanatec Stock and Clubsport shifter sets to minimize play in the shifter adapters, ideal for use with the XL20 and XL21 Xlerator Wheel Stands. The inserts accommodate 12mm rod diameters and feature 10mm...

I designed this dust cover specifically for the Fanatec CSL Elite Wheel Base. I prefer to remove the wheels once I've finished using them, so I created this cover to protect the DIN plug inside from dust and damage. February 11, 2019 Someone...

Universal HUD holder for Fanatec DD1 and DD2, with the possibility to use any type of cell phone, tablet, etc. on which you use Simhub. The model is very convenient to use both in terms of operation and simple placement. Components to be used: M5...

I wanted to add a damper to my Fanatec V3 pedals and decided to make my own. I order two dampers off Aliexpress for $5 each. I created the files in Fusio360 and printed on a Bamlu Lab X1C. ... ...

This is a remix of the magnetic shifter mod for Fanatec F1 steering wheel by joey99. I find this one the best implemented of all the available ones, however I had problems printing the small part and have now modified this one a bit so that it was...

(It's missing the top bolt since it's useless in this case) M12x1.5 thread is modeled, so it can be mounted directly to the shaft of the Fanatec SQ shifter. It's meant to be used in a simulator, no real world testing has been done. ... I have...

I created an adapter to be able to attach the Fanatec QR1 lite and 70mm aftermarket wheel to use with their wheel bases. I used m5 heat set inserts for the threads vs 3d printing the threads. Have around 24 hours of use time on it using the CSL DD...

I was not satisfied with the size of the original shifter paddles on the fanatec wheel so i remixed a model of the original part to fit my needs. The paddles were made about 1.5 cm taller plus i made the angle part a bit wider for a stronger...

I created a customized washer to serve as a spacer when attaching the Fanatec Handbrake to the Fanatec Shifter. When setting up the shifter on your right, I found the handbrake to be extremely close to gear shift while shifting into 5th and 7th...

I embossed the Fanatec 'F' into the back parts for this there is a left and right version which will need to be printed so it is the right way up on both sides when fitted. I have also included a blank one if you prefer that. Print with support...

For sure will be compatible with another Fanatec bases, but I cannot test it. Added an V2 which doesn´t need the gaskets, but need supports. Not tested, as the first version fits me perfectly, but it´s up to you. PD: Added a mobile phone version. ...

Installation: ========= * Install rear mounts (remixed part) with the 16 mm bolt in the hex hole on the mount and washer and nut * Install front mounts (original part) with the 30 mm bolt in the hex hole on the mount, use the included Fanatec Hard...