fan for ender 3 3d models

This is a revised version of my fan duct design that incorporates a holder for a dial indicator. The original design can be found on Thingiverse at https://www.thingiverse.com/thing:4528533. The holder itself has an 8mm diameter. ...I am using an...

Two additional fan mount options are available for the Ender 3 rear electronics case by TT, specifically designed for the right lid. The larger option is intentionally offset to facilitate easy installation without obstructing the motor. The...

I made this Because I own a printer that doesn't Exist - Or better, there is a severe lack of information about it Online (It's called EZT3D M09?) For my printer, which is oddly similar to the Ender 3, there is no compatible fan configuration as the...

This design works great for my Aquila and my Ender 3 V2 (and should work for other Ender 3 models). I ended up incorporating a Mini Me V4 style hotend cooler mount into the RHD Fan duct for MK3 Bondtech BMG Mosquito...

In this version, you use only stock Ender 3 parts (fans and mounting hardware) for installation. No extra parts are needed. The mediaman parts require M3 screws that collide with the parts cooler fan. Tested on Ender 3 (2019). Basically, I...

2 more fan mount options for the ender 3 rear electronics case by TT, these are for the right lid. The bigger one is not centered to make it easier to slide in avoiding the motor. The pic shows my curent setup with the 8010 fan on the left lid and...

This is a custom-designed fan shroud for my Ender 3 printer. It will also work on CR10 series printers. The design is intended to be printed using PETG or ABS materials. The hot end cooling fan draws air upwards and away from the print, reducing...

My specific use case has the stock Ender 3 driver board in the left compartment when viewed from the front, and an Orange Pi Zero in the right one using https://www.thingiverse.com/thing:3794903. These lids are only modified from TeachingTech's...

Based on the MBOT3D MK2_Rev2.0 by Ahmad Sunardi, I have designed this Dual Blower Fan Duct for E3D's RapidChange Revo CR Hotend installed on the Ender 3 V2 3D Printer. You can install it on a Direct Drive as well as Bowden setup. The magnetic...

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

This design works great for my Aquila and my Ender 3 V2 (and should work for other Ender 3 models).I ended up incorporating a Mini Me V4 style hotend cooler mount into the RHD Fan duct for MK3 Bondtech BMG Mosquito...

I really liked Allules's Hot End Cooler mod (https://www.thingiverse.com/thing:4163014), and used it for a bit, but I wanted to convert my Ender 3 Pro to direct drive. I tried Sashalex007's SpeedDrive v1 direct drive conversion...

Here is my first go at designing a fan shroud and duct assembly for the Ender 3. I mostly made this for fun but its also functional and someone might like trying it out. Keep in mind that this is a work in progress, there are many things that can be...

I'm excited to share my first-ever 3D model, a fan duct designed for the Ender 3 V3 SE with the K1/KE hotend. After thorough testing, I can proudly say that it functions flawlessly and significantly enhances the 3D printing experience on this...

[Updates at the bottom]Here is my first go at designing a fan shroud and duct assembly for the Ender 3. I mostly made this for fun but its also functional and someone might like trying it out. Keep in mind that this is a work in progress, there are...

This is an Electronics front enclosure for Ender 3 V2, it is designed to fit: Bigtreetech SKR 2 Raspberry Pi Zero 2 1x Noctua Fan 92x10 Needs the feet extensions already installed. For specific to the parts I had available and the limited length...

Since we don't have many good designs for dual 5015 fans part cooling available yet, and I'm kind of an enthusiast myself, I decided to do my own approach on it. Keep in mind I'm a total noob on Fusion360 and any CAD software, so it is not a perfect...

For this fan housing the stoc fans can be used as well as any other 40x40mmx10 or 20mm fan for the hot end, including the famous Noctua fan. I tried to make it as minimalistic as possible but without compromising his strength. The fan blows to...

A protective shield for the right side of the enclosure crafted by TeachingTech, featuring holes specifically designed for an 80 mm fan. Please note that a 25 mm thick fan will not fit within this configuration; instead, use a 10 mm thick fan...

This duct is very useful for a lot of Creality printers. ...It's mais function is to be an "easy to install" adapter for 5015 fans. ...STEP file is included in need of small adjustments.

... The Trianglelab BMG extruder without light pancake stepper motor can be purchased at this link: https://ali.ski/tb4kn. Additionally, a 5015 fan with dual ball bearing is available for purchase at this link: https://ali.ski/OhJKFB.

This remix of the eb Fan shroud and Adjustable BL-Touch mount was created to allow quick access to the hotend With this shroud mod: * Only two bolts must be removed to access the mounted hotend * The hotend and shroud are now separated, they can be...

After destroying two fans so far, I decided that the Satsana fan housing needed a cover. I looked around at the free offerings and found nothing to inspire me, so here is my version. It is 3mm thick and will work with an original 40mm x 10mm fan or...

I had a clocked hotend (cool end) several times now and wanted to upgrade the fans from 40x40x10 to 40x40x20 to improve air flow. ... This one is a remix with cutouts on the fan side so the air can flow freely.

I really liked the original model but I noticed a hole in the duct that would let air through. ...so I patched it in blender. it's a quick fix so It might not be perfect but it does the job :) The offsets for the bltouch: X=0, y= -40, z= -2

He made a version for the MicroSwiss Dual Gear Extruder, but I like this one better. So I modified it slightly to mount the BLTouch. The offset is x58 y-9. ... If you enjoy this remix make donations to the OG designer so he keeps up the great work.

This is a custom Electronics front enclosure designed specifically for Ender 3/Ender 3 Pro users. ...It's engineered to fit perfectly with these popular models: * Bigtreetech SKR 1.4/1.4 Turbo boards * Raspberry Pi 2/3 computers * Four LM2596 power...

This is an innovative Electronics front enclosure designed specifically for Ender 3/Ender 3 Pro, perfectly tailored to fit:\r\n\r\nBigtreetech E3 Mini\r\nRasperry Pi 2/3\r\n4x LM2596\r\n1x Noctua Fan 40x40\r\nThe design has been cleverly divided into...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech E3 Mini Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join the parts and...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech SKR 1.4/1.4 Turbo Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join...