fan for ender 3 3d models

This is a new design for all Creality Ender 3 printers (excluding only Ender 3 S1), CR-10 and Ender 5 Plus with Micro Swiss Direct Drive Extruder along with the original BLTouch metal mount. Inspired from Satsana 5015 Fan Duct and Orbiter Fan duct,...

Things I changed: Shaved a little off the top plate to make room for the motor Removed the wasted space under the front fan for viewing the nozzle Shortened the BL Touch tab Added a hole to run wrench through front to mount the duct Cleaned things...

Things I changed: Shaved a little off the top plate to make room for the motor Removed the wasted space under the front fan for viewing the nozzle Shortened the BL Touch tab Added a hole to run wrench through front to mount the duct Cleaned things...

This is a remix of the Satsana 5015 Fan Duct from eric_anastas modified to fit "ALL" Creality Ender 3 printers (excluding only Ender 3 S1) and CR-10 with the Micro Swiss Direct Drive Extruder using the "original" BLTouch metal mount. It's been...

I designed this to eliminate heat creep in my stock hot end with all metal heat break and also to eliminate any other unwanted noises caused by the Hero Me fan guards and my Winsinn 4010 fan.

I keep exploring diverse fan configurations for part cooling and want to verify them through hands-on testing instead of solely relying on online reviews. To achieve a cleaner setup, I designed this box to simplify wiring and mounting JST connectors....

A Remix of "Ender 3 Fan Shroud for 4020 Fan - No fan guard by Freich". Added some Ribs for printability without support. ... Also did some slight design changes ;)

The stock fan on the Ender 3 Pro had a short lifespan, prompting a search for a quieter and more powerful replacement that runs on 24 volts like the stock fan. Most 40x40x10mm fans available in 24 volts are extremely loud or fail to provide...

This is a Fan Duct for the stock Ender 3 S1 Fan. Since -in my opinion- the stock Ender 3 S1 Fan isn't as bad as some say, I designed a Fan Duct which directs the air to both sides of the print in order to reduce warping and get a more uniform...

I bought a micro swiss full metal clon for cr10 and use this in one ender 3 but the default fan duct is short.

A simple Ender 3 / Pro fan duct to attach a Noctua 40x40x20mm (Noctua NF-A4x20 FLX) fan instead of the original one. The original part-cooling fan can be attached on the right side. You can use all the original screws. Be careful: The Noctua Fan...

Compatible with "Ender 3 60mm Board Fan Cover": https://www.thingiverse.com/thing:4902986

This cover protects the PSU fan of the Ender 3 for outside installation. It should fit any 60 mm by 60 mm by 25 mm fan perfectly. The Noctua NF-A6x25 fan I initially intended to use wouldn't fit inside the casing, so I removed the metal fan cover...

This cover for Ender 3 power supply has room for 25mm fan. It also has place for 2 step-down converters and 2 switches. ... Result in this video: https://youtu.be/RZsrXKKNnhU

... utilize their Ender 3's built-in vertical fan, expanding its functionality and capabilities. ...Specifically designed for seamless integration with the Ender 3, this adapter unlocks new possibilities for improved print quality and reduced noise levels.

This is a remix of the [Satsana Remix for Ender 3 Pro by scottyujan](https://www.thingiverse.com/thing:4794720). Since the centrifugal fans that I have ordered / used so far are too loud or start whistling / squeaking after a while, I created a...

The accessory is specifically designed for the Ender 3 and comparable models, attaching securely to the side of the standard extruder casing. ...Several similar designs are already available on Thingiverse, but this one raises the fan a notch higher,...

▷ Update fan wind test new movie (22-3-19) Regarding the issue of the installation angle of the filament cooling fan This remix has been modified to suit my cooling fan and printer settings. I am satisfied with the cooling breeze provided. We...

But I am happy with the performance so far.I accidentally printed the model below without supports with steep overhangs and a 11,8 cm  bridge and it printed beautifully at 80-180...

Hello Makers, Recently bought Micro Swiss direct drive extruder kit for Ender 3 and CR10. Great gear, there are small issues with limiting printing area in Z but I will work on it soon. Quality of print is greatly improved and I can finaly use Linear...

Hello Makers, Recently purchased a Micro Swiss direct drive extruder kit for my Ender 3 and CR10. Great gear, but there are some minor issues with limiting the print area in Z that I will work on soon. The quality of prints has greatly improved, and...

I made this project for one single purpose : replace the original ultra-noisy hotend cooling fan of the Ender 3 Pro by the much quieter and efficient Noctua A4x20 fan. I wanted to keep everything else as is (with some minor adjustment) so original...

I created these to Fit my Ender 3 Max as i added the Creality Spider Hot End

Print head with direct extruder for 3 d printer

... easier to print in the upright position. I didn't use supports for the fan housing. I printed the ducts with the bottom flat side on the bed. *I didn't see the pro version locking tab had the screw already. ...That would have saved me some time.

This doesn't require any mounting hardware for the fans they are a tight fitment. You do have to use the original bolt holding the shroud on. ...Supports aren't really needed unless you feel the need to use them.</p>

... by 0.4 millimeters. Initially, I was dissatisfied with the appearance of the stock fan when paired with the Bullseye fan. ...In response, I created a custom cover that features a snug slip-on fit, effectively concealing the black fan from view.

I required an effective means of mounting the standard part cooling fan following the upgrade of the hotend extruder fan duct to this: https://www.thingiverse.com/thing:2160958. This new setup offers significantly increased visibility and is...

This modification adapts a 40 mm radial fan to fit into the blower fan opening of the Hero Me V6 Fan Duct. It works perfectly as is, but there's a small issue with the inside of the hole where it attaches to the top of the Hero Me unit. Don't worry,...

... drive upgrade and put a Slice heat break into it. ...The original is to tall to fit, so I cut off the top in 3D builder and printed this one. Fits perfectly... I love this fan shroud....I can print LW-PLA at 255c without heat creep that creates jams.