fan and filter 3d models

This is a custom-built filter/fan unit designed to be installed in my enclosure, taking on the role of a particulate filter assembly rather than simply extracting and ventilating outside air. ...It utilizes standard car cabin pollen/carbon filter...

Fan duct and filter barrier. ...Scale according to your needs.

I designed this then found ANDIMOTO  had already created something similar just not for my fan so i am tagging original designer below.ALSO CHECK OUT KREME FAN FILTER FOR THE DIMENSIONS AND LINK TO THE FILTERS. TESTED AND WORKS GREAT MOVES AIR...

The key advantages over many other solder fan stands are:The model is easy to print without support.The filter fits in tightly so no air escapes around the filter.The filter is still easy to change.Easy assembly, as only one part needs to be screwed...

There are plenty of enclosure fan/filter mounts out there, but I couldn't find exactly what I was looking for - maybe this will suit someone else's needs too! The body of the mount is fixed to the enclosure (in my case, a plywood box) using #6...

So I redesign a 120mm modular setup for the fan and filter. Also I have no idea how the screwing was suppose to be done on the original design so I included access hole from the inside of the adaptor. You can stack those as required, as a push or...

I wanted to minimize plastic use for the fan box and enhance air flow, so I reworked a 120mm modular setup for the fan and filter. Additionally, I was unclear about how screws should be attached in the original design, so I included an access hole...

There's a filter ring using pantyhose filter to keep dust out of base if you use this 80mm fan as intake for your base. If you need more information on the usage of the filter ring, please see my build post at...

Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...

Air vent box for ANYCUBIC PHOTON MONO SE using 3M Organic Vapor Cartridge 3311J-100-S1 and 12V Fan AV-F7530MB. You can swap the back panel of the printer with this. 12V can be drawn from the original fan cable inside of the printer. ...I added a DC/DC...

That way, you can rotate the filter holder and it will allow the fan and hose to remain stationary while it screws apart. Note that "Filastruder_fume_extractor_male_threaded_4_inch_duct_holder.stl" is the same model as from the Fume Extractor thing,...

This allowed me to rotate the filter holder while keeping the fan and hose stationary during disassembly. Note that "Filastruder_fume_extractor_male_threaded_4_inch_duct_holder.stl" is identical to the model from the Fume Extractor thing, with no...

Didn't want the bulk and cost of a commercially available "portable" airbrush booth so decided to make my own with a portable photography lightbox available online for $15 and a couple of 80mm fans. Step one... Cut a hole in a box. ...

Download .stl files and an NX .prt for instructions on assembling the duct, fan attachment, and filter. Alternatively, use granulated carbon with two small pieces of filter to simplify assembly. Attach the duct assembly to the z stage, screw and...

... 3. I wanted a filter that was quick to clean and maintain, so I designed this holder. Purchased these filters; https://www.amazon.com/dp/B01DIYRK52 They should fit perfectly in the filter holders, but as stated, the design has not been tested yet.

Hi, I made this as a filter to stop dust and Bits being sucked in by the side fan. The small Rectangle part slots into the filter, I glued a bit of dust proof material on it first. I added Small Sd card slots, two little compartments for my...

The Orion accessory set includes a filter, housing, and guard to enhance your photography experience. The filter helps control light exposure while the housing protects the lens from damage. ...The guard, on the other hand, prevents glare and unwanted...

... using fan blades from a 120mm computer fan. ... The fan is positioned behind a wall and connected to the system via a detachable hose. ... This project was designed with Tinkercad; it can be edited online at https://www.tinkercad.com/things/g200c7MpGfG

I wanted to add an exhaust fan to my Original Prusa Enclosure, however the solutions I found here didn't fully match what I wanted, which was a solution for a 120mm fan with HEPA and carbon filters, which are readily available in Germany, and flaps...

Finally got round to tweaking my Hepa filtered storage box build (alternative to still air) on a budget. £50 roughly in total. ... https://www.youtube.com/watch?v=QGkhJEhuLz4&feature=youtu.be&ab_channel=secondharvestimvu

Finally got round to tweaking my Hepa filtered storage box build (alternative to still air) on a budget. £50 roughly in total. ...https://www.youtube.com/watch?v=QGkhJEhuLz4&feature=youtu.be&ab_channel=secondharvestimvu

I'll print your 140 mm and 120 mm fan dust filter holders to cut down on dust in the computer case. The design features voronoi patterns, I hope people haven't grown tired of voronoi yet. The 140 mm filter allows for mounting a 120mm fan. ... **Check...

... to shield a Stage Acoustics PPA1200 audio power amplifier from dust particles that can damage its internal components. ...By reutilizing the existing grid, I made it possible to easily attach filters or clip-on accessories directly to the unit.

Parts List Fan: https://www.amazon.com/gp/product/B009OWVUJ0/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 Fan Speed Control: https://www.amazon.com/gp/product/B00809BQZG/ref=oh_aui_detailpage_o02_s02?ie=UTF8&psc=1 Carbon Filter Pad:...

Parts List: - Fan: https://www.amazon.com/gp/product/B009OWVUJ0/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 - Fan Speed Control: https://www.amazon.com/gp/product/B00809BQZG/ref=oh_aui_detailpage_o02_s02?ie=UTF8&psc=1 - Carbon Filter Pad:...

Human: Reduce the size of a 120mm dust filter to fit an 80mm space by shrinking it down to 66.67%.

My remix is a bit higher to fit 120mm PC fan combined with filter (this part is work in progres, I want to update filter placement) * One back side feet has hole to thread small pice of ptfe tube in it as a filament * guide - so filament sensor may...

High-performance fan solution for 540-size RC car motors employs a 30mm duct to optimize airflow and minimize heat buildup, secured by reliable double-sided tape and robust M3 screws.

An adapter created to attach a 80cm 5V computer fan to a grow-op style charcoal air filter which can be hung inside a 3D printer enclosure to circulate and filter air while printing to remove headache causing odors. Creates a gentle air circulation...

Air Cleaner-Box for 120mm Fan and Hepa H12 H13