face mask with neck strap 3d models

To hold the face mask on your face.

A face mask holder with support for neck. You can use an elastic strip to prevent this to fall down. There are also two holes if you want to use an eyeglasses holder. ...Three version for 118, 112 and 911 staff.

This is a face mask extension strap. ...Made out of plastic. This holds the mask straps with better ease, and allows the face mask strips not to extend much.

best face mask strap print in 60 percent infill

This strap is intended to remove the pressure of the elastic strap of a face mask from the ears of the wearer. ...It is thin and flexible when produced with PETG filament.

This is a clip to adjust the length of round (elastic) face mask straps.

A new design 3d printable face mask strap . ...another file inside for fast production .

This is a clip to adjust the length of round (elastic) face mask straps. ...

centipede strap for face mask this mask strap goes on the back of head to secure typical face masks I designed this in 2019 and have been altering it as time passed and received feedback from locals.

This is my interpretation of a face mask strap to relieve stress on people's ears from daily wearing of face masks. These print thin enough that they are flexible using PLA and are comfortable to wear. Each strap takes less than 20 minutes to print.

This is my interpretation of a face mask strap to relieve stress on people's ears from daily wearing of face masks. These print thin enough that they are flexible using PLA and are comfortable to wear. Each strap takes less than 20 minutes to...

This a really simple face mask strap that I designed for health workers during the COVID-19 outbreak. It's the bare minimum, with simple and soft curves for easy and fast printing. ... This model can be edited at...

This design allows for printing a large volume vertically, >50 straps per 230x230mm build plate, of face mask straps in one go. ... The facemask strap is printed vertically the end-user may then dip the strap in boiling water and mould the shape to the...

Quick release adjustable face mask extender/adapter. ... Print a pair with PETG(recommended)

... five minutes of print time of the other one I was using and is smaller so I can print more in the same amount of time. I update the file today to make a cleaner version. Mask Strap Simple prints fast and clean and is optimized for a 1mm nozzle

Perhaps a bit late - but most / all other face mask straps are pretty badly designed. They tend to need retractions / travel moves, require infill on the tips, or have infill meet perimeters in strained areas, reducing durability. This strap is...

I designed this face mask holder / strap in 4 sizes: 72mm, 85mm, 100mm, and 115mm. I uploaded the 100mm design but if you'd like to change the size then scale the length only by +-15%, this should do you well. I've designed a few of these mask...

I designed this face mask holder / strap in 4 sizes: 72mm, 85mm, 100mm, and 115mm. I uploaded all four sizes but if you take the 100mm design and change the scale size in the length by +-15%, this should do you well. I've designed a few of these mask...

This is a redesign because my kids kept loosing the straps. ...So now one side can be connected to the mask-strap. ...

Heavy Duty Strap for FFP2 Mash I was fighting a lot with current designs currently on Thingiverse I have really curled hair it was a nightmare to remove the hooks from my hairs This model was Tested with Ski Helmet, and it fits nicely on top of a ski...

I redesigned "Sew-in Quick-Adjust Elastic Connector for Face Masks" to: - work for typical shoelace - shorter, simpler, quicker, work for rigid filament (PETG works great) For the part that is to be sewn into the mask, either: - Use model without sew...

My wife was busy making face mask for COVID-19 and was looking for a buckle. This Buckle is design to hold ¼” elastic for light weight uses. The elastic can be tightened by pulling on the end of the elastic and can be released by lifting the lever....

Print in sets of 2. ...Loop ear bands through the hole and pass it around the end of the strap, then pull tight to secure. These stay attached to the mask and are very simple to put on and take off. ...Originally printed on Markforged using onyx.

simple mask holder. ...added the ipt file as well for you to customize

I found that single piece designs would not remain attached to the straps under all conditions and string diameters. This two piece design allows the straps to be attached in a closed loop attachment that never fails ( under reasonable use... ...) The...

This thing was made with Tinkercad. ...Edit it online https://v1.tinkercad.com/things/8s0JlEXkVqB

It is 0.4mm thick so it remains flexible printed in normal PLA. ... The post is on one side to let you peel it off the bed easily. Just trim the post off with flush cutter when it is complete.

... is on one side to let you peel it off the bed easily. Just trim the post off with flush cutter when it is complete. ...Print Settings Printer: Artillery Genius Rafts: No Supports: No Resolution: 0.2 Filament: Generic PLA Category: Accessories

... post is on one side to let you peel it off the bed easily. Just trim the post off with flush cutter when it is complete. Print Settings Printer: Artillery Genius Rafts: No Supports: No Resolution: 0.2 Filament: Generic PLA Category: Accessories

Face Mask Strap Ear Protector