f 14 3d models

this is a personal design I did just for fun,f-14 advanced tomcat is a f22 raptor mix on grumman tomcat multiple formats. ...modeled in rhinoceros 5

i remixed hampstonaters f 14 to fit with a model pane stand by marcpv here https://www.thingiverse.com/thing:796579 for a fathers day present also i made a top gun stand aswell that also works

DescriptionGrumman F-14 Tomcat Lowpoly model of american jet fighter Grumman F-14 Tomcat is an American carrier-capable supersonic, twin-engine, two-seat, twin-tail, variable-sweep wing fighter aircraft. The Tomcat was developed for the United States...

... early 1970s. ...Its design combines speed and agility with state-of-the-art avionics and armament systems. The F-14's primary mission is air superiority, but it also excels in maritime strike roles, anti-submarine warfare, and reconnaissance missions.

I designed this external wing tank for the Freewing F-14 Tomcat. I have yet to print this part, but I will update this as soon I do. There are five parts. The Nose, Center, Rear which makes up the main tank. Then the pylon on and wing mount. ...The...

Sidewinder scaled for Freewing F-14 Mid section has breakaway pads to help stabilize it during printing. Print the mounting lug solid as it needs to be strong. The rest can have minimal infill. The lug is standard Freewing dimensions. ... A socket...

To adjust the end-tube of the freewing F-14 to optimize it for the FMS EDF a small tool. ... Glue sandpaper on the cone and the cylinder and sand it, till it fits, than seal the surface with tape or parquet-laquer

I have designed 3D printable replacement ventral fin for the Freewing F-14 80mm EDF Jet. This is very easy to print (lying flat on the print bed). Please be aware that the 3D printed ventral fins may be heavier than the stock Freewing wooden...

I crafted an external wing tank for the Freewing F-14 Tomcat from scratch. As soon as I get my hands on a 3D printer, I'll be updating this project with live photos of it in action. ...This ambitious design consists of five intricate parts: the Nose,...

I have designed a simple fuel dump port cover for the Freewing F-14 Tomcat 80mm EDF Jet. Some trimming of the stock foam fuel dump cover may be necessary to fit over it. It should be a snug fit, but should be glued on to ensure security. ... As...

I added a servo to create a moving tailhook on the Freewing F-14 80mm EDF jet, and needed a means of shielding it from wires accidentally inhibiting the tailhook servo operation, so I created a simple shield to help keep the tailhook servo separated...

This package contain a Jet Fighter Aircraft 3d model, that looks like a F-14 Tomcat. All parts of the model were made in full accordance with the original. Each dynamical part, like ailerons, wings or chassis, are separated and have correct pivot...

I didn't care for the cheese grater appearance of the Freewing F-14's lower fuselage, so I decided to take matters into my own hands. I printed two custom intakes and cut a new thin plastic sheet to replace the perforated one. It now looks much...

There are also other models from the movie so check them out: The F-14 The F/A-18 Super Hornet The DarkStar This model was made possible due to previous models that served as inspiration: The Articulated F-14 by agepbiz The F14 Kit Card by toto_28...

Update v1.1 - 22 March: Alternate Parts for smaller print bed - 210 x 210 x 240 mm Other minor improvements To get this update, simply redownload the files RC aircraft of the F-14 Tomcat. ...Has all moving tail and swing wings and is powered by two 50mm...

I have designed a main wheel-well Side Covers for the Freewing F-14 80mm EDF Jet. This is not meant to hide/conceal the main wheels, but rather make the main wheels look less noticeable when the gear is retracted, as well as fill the noticeable gap...

I have designed screw hole plugs for the wing box cover on the Freewing F-14 Tomcat 80mm EDF Jet. These plugs are placed inside the foam holes after screwing on the wing box cover to conceal the screw holes for better visual presentation. The...

Blank Panel

Print SettingsPrinter Brand:CrealityPrinter: Ender 3 ProRafts:NoSupports: NoResolution:0.16Infill: 10-20%Filament: AddNorth PLA

My next idea for Tomcat is presented here.

Covers to make toggle switches easier to identify

Tomcat (ala Top Gun) is a surprisingly big plane; in fact, it was the biggest plane on board until our world cruise when we had an EA-3 Whale (Skywarrior) that had a sign on the side "on loan from the Smithsonian". Again, no loadout or missiles...

The idea presented here revolves around Tomcat, which serves as its primary subject matter.

Note _________________ Print Thin Walls

Print SettingsPrinter Brand:CrealityPrinter: Ender 3 V2Rafts:NoSupports: NoInfill:10-20%

Note

Little baby jet :) This model has in-model supports. But generating support in slicer is needed also. ...Have fun with this :)

No description provided.

Individuals: People who are not robots.