eyeglass frame 3d models

I'll share here the printable parts I've used, as a frame for learning or trying a different method of locomotion in robots. There are many quadruped robots designs on Thingiverse, my design uses 5 servos for locomotion instead of 8 or more. On the...

The negative side connects to the negative input side of the over-charge connector and to the negative input side of the speed controller.The output side of the over-charge module then connects to the control side of the relay: positive to connection...

I'll share here the printable parts I've used, as a frame for learning or trying a diferent method of locomotion in robots. There are many quadruped robots designs on Thingiverse, my design uses 5 servos for locomotion instead of 8 or more. On the...

This third part has a fixed distance between the top and bottom cones, and a fixed width, to fit into the adjusted tool holder when writing.The tool cradle has been redesigned to fit tightly to the printer using three specifically designed T-shaped...

You'll need 8 of these. Assembly InstructionsOnce everything is printed follow the steps below.Please note, much of this will just push-fit and clip into place, but some parts such as the door handles, keyhole, and possibly the windows, may require...

Tray frame for metal plate (195 x 175mm) Tray for metal foils (195 x 175mm) Tray for magnets (5x2mm and 3x2mm holes)   Assembly Video SuperProBox   Equipment & Assembly Dashboard & Adapter Grease Superglue To ensure a smooth snap and gliding of the...

The only issue was some tiny misfits on the X carriage frame, the tolerance for all screw holes are just fine, the issue was only the two big holes for the stock hotend mounting bulges, I drilled them a little bit to make them fit. Anyway I will fix...

They required more pressure to screw in, but seem to hold securely. If the main extrusion frame is the same dimensions, this should work for other printers. The purple/grey printer is an Ender 3 Pro with an SKR Mini E3 v3.0. For the “E3_Chassis_x”...

The techno-organic heart in its chassis was beginning to mutate and fuse with the skeleton in its frame expelling inorganic material, growing new nervous systems, new muscles, new organs and a new brain.ABOUT THIS 3D FIGURINEThe model is saved in STL...

Place the hammer through the slot in the top of the frame, through the hammer braces, and slide the pin into place. Use the thumbscrew or the punch to push it through. (You may have to run the pin through the hammer a few times before installation,...

... on using the MGN12 alignment jigs. Attaching the blocks and carriage should be self explanatory. Use the original bolts that were used to mount the wheels. Remount the whole assembly using the spacers between the Y extrusion and the main frame.

- OpenLOCK: drop 6 mm from bottom of tiles - DRAGONLOCK: drop 5.28 mm or 5.21 mm (depending on tile set) from bottom of tiles - Tilescape: drop 6.4 mm from bottom of tiles with integrated frame, nothing to drop for frameless tiles 3. Print a plug...

Chronologie :10/08/2021 : Disponible à la vente en ligne (système entièrement monté et testé) :...

The only issue was some tiny misfits on the X carriage frame, the tolerance for all screw holes are just fine, the issue was only the two big holes for the stock hotend mounting bulges, I drilled them a little bit to make them fit. Anyway I will fix...

Any prospective assemblers will need to pay attention to how I have constructed my bottom frame, with the two wide 2020 extrusions, set back 20mm from the front and back of the bot. The models were printed in solid ABS, using a 0.8mm volcano nozzle...

- 1 x **3.3V to 5V logic converter**: From local electronics shop - A set of **[JST SM connectors](https://www.amazon.de/-/en/dp/B087M1M2HC)**: to connect the displays - 1 x **[ESP...

Bronco_Rear_Quarter_Short_V2.stl is a 5mm longer rear quarter to better fit the TRX-4 chassis because the TRX-4 frame is about 25mm longer than an SCX10 or clone (I missed it by those 5mm the first time). Note that my build is the original and the...

Sandpaper the cut surfaces and glue them together with Loctite. The hassymountdiy.stl may serve as a starting point for making your own lens cone. Lensboard: Sandpaper the surfaces and glue them together with Loctite. Two variants of...

Please review the filenames, model file comments, and pictures before starting.Non-printable parts and necessary tools:The clock movement and clock second...

Bronco_Rear_Quarter_Short_V2.stl is a 5mm longer rear quarter to better fit the TRX-4 chassis because the TRX-4 frame is about 25mm longer than an SCX10 or clone (I missed it by those 5mm the first time). Note that my build is the original and the...

If installed incorrectly the spade connectors will hit the hyperpixel screen and you won't be able to connect the power wires to the switchSolder a female breakout wire to ground to the SparkFun USB-C Breakout BoardSolder a wire from the SparkFun...

Assembly: - While you can just glue everything together I used a mix of gluing some parts and bolting the frames together. - Sand edges (or exacto) to remove all elephants foot expansion and fill/sand to your desire. Then paint pretty much all...

### Sling A sling is pretty much required as it allows the frame to be dropped when using different two handed weapons e.g. pistols, grenades. Any random cheap rifle sling (e.g. used for airsoft) should work. e.g. -...

The only issue was some tiny misfits on the X carriage frame, the tolerance for all screw holes are just fine, the issue was only the two big holes for the stock hotend mounting bulges, I drilled them a little bit to make them fit. Anyway I will fix...

Be careful not to damage the input jack for the power connector. Your'e done  Step 10 Insert the the window, followed by the plastic frame with the knobs and then mount the controller board. Use the orignal screws.Connect the wire for the input jacks...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

Be aware, that when finally screwing the lamp foot together, simultaneously counteract the twisting of the electric cable inside (un-twist the cable through the exit hole in the lamp foot) How the lamp shade modifiers are set up As an example, this...

If you've got an enclosure or frame, it might be preferable to mount it with the trigger on the front.Additional Hardware Required:0.5mmx3mmx10mm 304 Stainless Steel Compression Springs (2)M2-0.40x3mm 12.9 Hex Socket Set Cup Point Grub Screw (1)9mm...

It is a pretty archaic machine, so enough to tinker and update :)You can create a simpler handcrancked version with the parts to begin with.Is this machine too simple for you, take a look at the machine+ created by Warpster. Frame:I made the...

Please let me also know how you rate the design.Unfortunately, the uber fidget ring was deleted due to a design claim, so its no longer available.If you like it, you can check out the dual fidget ring:And the discrete (as in discontinuous/quantized)...