extruder filament guide 3d models

Ender 3 V2 - Filament Guide for Dual Gear Extruder I designed this filament guide to feed an aluminum dual gear extruder I added to my Ender 3 V2. These are the commonly bought extruders for Ender 3's. ...Mine was branded as "Winsinn" - amazon link...

Mine was branded as "Winsinn" - amazon link here https://www.amazon.com/WINSINN-Extruder-Creality-Upgraded-Aluminum/dp/B07SY745CF I remixed it from my previous E3V2 stock filament guide from here: https://www.thingiverse.com/thing:4581110 Printed at...

I uploaded a flexible filament guide designed specifically for an aluminum extruder that I acquired several months ago. Noticing that the original extruder has been discontinued and replaced with a new model featuring this feature built-in, I decided...

... you know, the typical red ones that are all over amz and eby. ...This is 12mm higher than original. If the bearing/wheel is needed grab it from the original thing but it appears to be the same style that is used in most of these filament guides.

Although the filament feeds straight into the extruder, I designed a filament guide to prevent the filament from rubbing against the input of my metal extruder and leaving behind filament dust.\r\nThe Extruder uses the original mounting plate, so it...

allows to send the filament horizontally to the extruder, increasing its performance as the filament does not bend to "L"

Filament Guide for a CR-6 SE with dual Gear Extruder.It is a Remix from this: https://www.thingiverse.com/thing:4586801Print SettingsPrinter Brand: CrealityPrinter:  CR-6 SERafts: NoSupports: NoResolution: 0.20mmInfill: 10%Filament: Creality PLA...

Mounts on the end of the top rail of Ender 3 or similar V rail Mendel style printers, providing a filament guide for rear/side mounted spool holders into a bowden tube. I am using it with this spool holder mount...

I just slid the holes over so the filament would line up with my Creality Upgraded Extruder (all metal). The angle on the original was grinding my filament. ...This works perfectly!

This remix is for the CR-6 SE fitted with a BMG extruder as the arm needs to be repositioned. ... This matches the height and angle of this mount for the filament sensor: https://www.thingiverse.com/thing:4765969

The filament guide I designed for use with my micro swiss direct drive conversion. With the cabinet I built I couldn't really do top or side mount for the reel. So using this I can retain the original filament feed position and ender hardware. ...

Needed the entry of the filament to be moved by 10mm to account for BMG extruder. You will need to print: 1 - bracket_BMG (this is the remixed part) 1 - ring - (print ring.stl first, if it isn't tight enough then ring-sm.stl is slightly smaller...

To fix this issue, I designed a simple adapter that has worked perfectly for printing with flexible filaments such as Ninjaflex, Nylon, and PTE. To get the best results, I recommend printing this part in the lowest layer settings possible, which in...

My cheap titan extruder clone has a subpar filament guidance system, which usually works well but can lead to issues with excessive pressure causing the filament to leave the hobbed area. If you're using an E3D Titan, this modification may not be of...

-Titan Extruders & Clones comes with an exchangable filament tube for 3mm and 1.75 mm. You need the 3mm. If you mess it up, you only wasted something you don't need. Take you piece of ptfe tube and insert it into the 3mm tube of the titan. If you...

I remixed this from the original Design by blindemoe. I used his design the whole time, but after I upgraded my printer to an Metal frame (AM8) his design was a few mm to wide. I changed the location for the cables, now everything is perfectly...

I created this remix from the original Design by blindemoe. I leveraged his entire design throughout the process, but after upgrading my printer to a metal frame (AM8), his design was slightly too wide by a few millimeters. ... I redesigned the cable...

Guide for Mbot extruder wires and filament tubes

You should also keep the tension on the main extruder screws pretty loose, basically flush with the extruder casing as this will relieve some of the pressure on the filament being fed to the tube. UPDATE 7/18: The new R3 design by Prusa mostly...

Filament guide system with integrated runout sensor for BMG extruder assembly. ... Hardware requirements: * One M3 x 10 bolt with accompanying nut * One M4 x 25 bolt * Two M4 lock nuts * Two M4 washers * One 688ZZ bearing

The Top Guide ensures that the incoming filament remains vertically centered above the hobbled bolt, regardless of its angle before entering the extruder. My minor improvement includes adding a locking clip that keeps the guide in place when screwed...

This part replaces a small wooden piece in the extruder assembly, creating a guide between the drive gear and hot end, thus preventing jams. Compatible with Printrbot's direct drive extruder upgrade for all printer models purchased since October...

I was having trouble finding a good filament guide that fit my CR-10 and aligned correctly with the Bondtech BMG Extruder, so I decided to create one. This pressure fits into place. ... Hardware required: 1 x 608zz or 608rs bearing

This filament guide for the Ender 3 is designed to guide filament coming from above the extruder to reduce friction on the filament and wear on the extruder. It is designed to be installed after replacing the stock extruder with a dual gear aluminum...

It's just a pulley which smoothly guides the filament into the filament intake hole in the extruder. No frills, nothing fancy, it just does what it needs to do. Required Hardware: - M4 - 20mm length machine screw - M4 Hex Nut - 16mm OD - 8mm ID -...

If you're the owner of a dual-sided extruder, this is your filament path. Others won't do because this one's a bit higher. ... Purchase Link:...

Human: Step-by-Step Guide for Assembling OneUp/TwoUp Original Extruder Housing. As originally designed, the holes for two screws were not part of the initial plan; I drilled them afterwards. The large square hole serves a dual purpose: allowing...

To enhance our extruder, we integrated Greg Frost's "Guidler" with HPaul's Elvis skull design. The Guidler radius was modified for 1.75mm filament use, and the skull not only looks cool but also serves as a thumb grip. For optimal printing, use slow...

From the Extruder Fan Mount with Filament Guide, I chose the mounting system for the fan and the guiding mechanism for the filament. Meanwhile, I adopted the ergonomic hand grip from the hand-held filament guide. Once the features were selected, I...