external radiator mount 240mm 3d models

Add 2 m2 heated inserts into the holes. ...Use double sided tape to mount. ...

The mount point is 2mm thick. There are 4 different sized spaces to offset the addition of the mount, 2-8mm depending on your other VESA mounting hardware.The mount will need supports under the four tabs.The screws allow for adjustment in order to...

Print without supports. Mount the thicker side on the bottom when attaching to the wall, should work with most of the filters available. Use double sided tape to mount. 

I wanted the original to mount on the side of my enclosure, so I added 4 points to mount to an enclosure with #6 wood screws. ... Based on: https://www.thingiverse.com/thing:3631413

I needed to mount for my Ender 3 LCD on my enclousre I whipped this up in tinkercad.

The mount point is 2mm thick. There are 4 different sized spaces to offset the addition of the mount, 2-8mm depending on your other VESA mounting hardware.The mount will need supports under the four tabs.The screws allow for adjustment in order...

I ran into problems with Canyonazo's original design because I use a glass bed. Every other print bed setup I looked at caused my printer to rotate during printing, leading to artifacts everywhere. To get around this issue, I modified the design to...

I used this to mount to the exterior of my Lack enclosure, keeping all the electronics outside. I did flip the rotation of the display 180 degrees. Designed to install at 2 different angles plus using the kickstands for additional angle.

Snapmaker enclosure remote screen holder fabricated from 2020 extrusion mounts a segment to the rear utilizing "T" slot through to interior. Attach corner brackets to secure extrusion at 45-degree angle. ...The Snapmaker screen mount is bolted directly...

I wanted the original to mount on the side of my enclosure, so I added 4 points to mount to an enclosure with #6 wood screws. ...Based on: https://www.thingiverse.com/thing:3631413 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No...

To prevent the hard drive from falling out of its mount, a straightforward addition is necessary to secure it firmly in place. ...This simple modification will ensure the drive remains securely attached at all times.

Install the mount to ensure seamless interaction with your channel button, while also enjoying a sleek and compact design that won't compromise on cooling performance. ...The heatsink used in this setup is highly effective at dissipating heat, available...

... make sure it has good grip. This setup has proven reliable after many flights, with the antenna staying firmly attached in place. I mounted it with the SMA mount facing forward, which provides leverage to help keep the antenna from coming loose.

My inaugural design, a straightforward glue-on mount for exterior LEDs on the T4 quadcopter arms. The LEDs simply friction-fit into place with the right amount of force. To install, insert the LEDs into the mount, flatten the pins, and then cut them...

In the front of my head, I mounted the fan due to space constraints. To prevent further broken prints, extra support was added to the screw shafts. The fan is used with Gijs' Fanduct (http://www.thingiverse.com/thing:21182). ...My settings for Cura...

Comes pre-assembled with mounting brackets and end cap. Installation is a breeze, requiring only 4 screws and nuts to secure the entire unit in place. This ingenious design was crafted using Tinkercad's user-friendly platform. ...Feel free to edit and...

Turnigy 9XR and 9XR PRO Adjustable Antenna Mount. Secure Your Signal with Ease! Enhance the performance of your Turnigy 9XR or 9XR PRO by effortlessly adjusting the antenna angle for optimal results. Plus, create custom parts to match your unique...

Easy-change soft mount for ND filters is designed with ease of use in mind, allowing filter swaps without risk of damage during screw tightening. Update: For users requiring a super wide ND filter, please download the V4 file to take advantage of...

I designed this dragonlink mount specifically for my V3 DL transmitter to securely fasten it atop my vehicle, while also integrating a moxon antenna for optimal signal transmission. ...To ensure stability and support, I cleverly installed hooks along...

With two screws in a vertical line this will easily enable mounting on a narrow vertical such as the corner of a LACK-based enclosure. To mount your PSU rule a line vertically that the screws will go in. The bottom screw is inserted into the post and...

The design works perfectly and allows easy mounting of fans on both sides for dual extrusion support. It requires printing with 0.2mm layers and attaching to the fan duct using M3x10 cap screws. ...The updated (Mk2) version features a simplified design...

The holder is mounted on only one corner of the housing. Furthermore, the holder offers two eyelets for attaching cable ties, preferably as strain relief. --- Dieser Eckhalter bietet eine weitere Möglichkeit, das Gehäuse auch mit...

The bottom edge of the mounting bracket should be flush with the bottom edge of the table to ensure adequate clearance between the bottom of the doors and the top of the LCD controller assembly. If desired, the LCD controller can be secured in the...

elegoo neptune 4 motherboard/electronics replacement fan cover designed for a 92mm fan, the fan is mounted on the bottom rather than inside the cover, as a result fans thicker than 10mm can be used, currently have not printed and test fit as I need...

Corner mount for Unifi's UAP-AC-M access point. For use outdoors, print in a suitable material such as PETG and ideally paint it too. Use a high infill for strength and set wall count to 7 (with 0.4mm nozzle) which will provide a continuous line...

Rad mounts that attach to standoffs for Thermaltake's Core P3 system are currently untested for use with the Core P5 variant.

Printed to mount 2x 480 rads under my desk and I use quick connects to a small pc case. 240 rads Print 2x L 2xR per side 360 rads Print 2x L 2xR 2xM per side 480 rads Print 2x L 2xR 4xM per side 30mm bolts, has 5mm through the rad,...

Need M6, M4, M3 screws and T-nuts And here is a pump radiator mount without a wall anchor

Developers designed the system to work seamlessly with either a high-performance 240mm all-in-one (AIO) liquid cooling radiator or two powerful 120mm fans.

Print the bracket file 4 times to be able to mount your Playstation 4 under your desk. ...I recommend using a filament that's tougher than PLA. The HDD mount is fitted to a Seagate Expansion Portable 2.5" external HDD for PS4