explosive space 3d models

This world was discovered by scientists who conducted experiments on the curvature of spaces, but at that moment there was a violent storm and it hit into their building than caused an increase in the portal. So they spread throughout the earth and...

On the right can be seen a game situation, where the potential point values of the empty spaces are shown.The points are adding up to a score for each player. Tallied on a paper, or something, either after a given playtime or a target score, the...

Because the springs take a little bit more space, the size of the foot designed for use with springs is different from the foot that doesn't use springs. To accommodate for a round broom handle end a spring plate with a recess for that round end...

OpenLOCK clip file.The Screw Track Angled file I added for reference if anyone is trying to make modifications.OpenLOCK attribution: https://www.printablescenery.comPrint SettingsPrinter Brand:PrusaPrinter: I3...

Extra Storage space in a sealed environemt.  There are extra shelves in this  enclosure for storage.  It is also an excellent place to store filament, that need extra protection from the environment. This is a simple printer enclosure setup. You can...

My printing space allowed without cutting other parts to be enlarged to 190% (printing area 215 x 215mm x 220mm). I did find the missing lower half of the body on the internet, but the model was in terrible condition - it didn't fit the upper half...

I also wanted to be able to move it easily and store it vertically to save space.No more need to connect or disconnect the printed circuit on the 4-pin connectorNo more need to make bridges for 2-wire use, simply put the switch on the 2 or 4-wire...

It bears mentioning that every single element, including road components, have been deliberately and conscientiously arranged onto V-Ray planes existing at coordinate point (0, 0, 0) with careful attention paid towards achieving proper aesthetic...

This offset not only conserves space but also allows for the convenient removal and replacement of a single filament spool without the need to disturb the remaining spools. Among other benefits, is the flexibility offered regarding the location of...

There is enough space for this due to the extended 205 fuselage. In addition, I positioned a larger battery (1500 mA) as far forward as possible to avoid having to add more extra weight. Both measures are sufficient to achieve the CG - but this only...

Space is a little tight there. It would be nice if there was room for a 3 fan shroud like for a Delta effecter, but there’s not. I didn’t want to kill myself over something that I wasn’t going to use anyway so I left it at that. My linear bearing...

I left quite a bit of cable as I am not the best at stripping cables so I wanted space in case I needed to redo it. You can cut it much shorter if you are comfortable. The wires you are looking for are the red and black, use a multimeter to check...

Fractionally condensed space between fans. Update:14_07_19 Uploaded a 1mm & 2mm Leveling Spacers\Helpers Update:14_07_19 Uploaded torture test images. This is my second remix of kelokeras & Mediamans Hero Me Fan Duct. This remix involves the base...

I shrank the original box to save space and material, it is now about 210mm long instead of the original 230mm I believe (i could be wrong on the original size). I also had to widen the box on the two outside holders as they were like 1.2mm thinner...

Knowing that I need to keep the enclosure doors open when printing with PLA, I wanted to find a design that could hide/slide/remove the doors so they wouldn't take up space in my room. I searched all over the internet until I found a perfect remix...

If you can source a 55x55cm bottom panel, good for you - these are not needed.5V XL4015 buck converter for powering the internalsArduino Nano for temperature control, sensors, fan control2x 120mm fans with PWM and RPM sensing (4 wires)2.4" LCD from...

There is not enough space between my version of rear extruder part and Z-axis profile, but I can do much about it. Solution which I´m using is pull-out sleeve from the profile and leave there just cables as you can see at pictures...

- if you notice stringing you're too hot, better to go a little colder on this build and get fine lines rather than structural stability since the knife will not be stabbing anything or anyone (hopefully) Supports:YES!  Keep bed supports on only or...

This adapter plate provides me either 2 or 4 mount holes in the AMPS ~38mm x 30mm spacing. (Actual measurements on my SiriusXM XDPIV2 AMPS mount is 37.5mm wide x 30mm vertically, center-to-center.) I will be mounting my SiriusXM Onyx Radio the...

The surfaces of the printed models are so smooth that no seals are required, maybe just as a bit of vibration dampening but I think you can just leave them out and everything works as intended.If you want to print them, then you need for each...

Printing these parts requires an X/Y space of 200 x 200 mm, and a Z height of 220mm. Along with the STL files, this zip contains both step and parasolid files for all parts. Remix or modify however you want.</p><h3>Print...

Grate spacing is still 3mm, so I'm using 4mm dia carbon pellets. A full box is about 55g or 2oz of carbon. $27usd/6lbs.I changed the bottom vent duct to blow diagonally across the floor and better distribute the exhaust air. Also changed the "L"...

These guides align the transparent portal inserts and leave 6mm of space for your creativity. The guides measure 2mm deep, 8mm wide and 6mm tall. When adding cutouts for your inserts, I suggest you cut out 3mm deep instead of 2mm deep. The extra...

I added a little feature to prevent that.10/21/2022Initial upload with Proto 2 files.Improved hinge tolerance (the 1st one required a bit of sanding), and slightly enlarged to provide more storage space for the cable. Fitting the cable in the 1st...

So I removed some parts of plastic case using side cutters and drill 4 holes (with 135mm x 45mm spacing) instead: Design of the housing base was prepared to fit these holes. Electrical mods: The display of timer have to be raised about 16mm. This is...

Players place their stones on the game board on the free spaces. If a player places his stone so that his<br>opponent's stone(s) is enclosed in a row between his stones, he also gains the position of those opponent's stones and exchanges them for his...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

As seen in the photo of the measurement in the MK2 version, the optimal space between the firing hand and the end of the PVC tube is roughly 2 inches. If you have to adjust any of the measurements for your particular game, you can easily print...

It's best to glue this on once the electronics and servos are in place to avoid having to mess around with the cables in the small space but if you need to, tweezers come in very handy. Pi and Breadboard: The raspberry pi is just held on with...

The boss design leaves enough compression space to allow 120 degrees of rotation.  The lever return spring is a replacement spring for a door handle. A package of 3 costs about $12 Canadian. The product name is “SeroNi 3Pcs Replacement Spring for...