exoslide ender 5 plus 3d models

I remixed the previous version which was not centered with the nozzle. I corrected the nozzle relief placement. I then made another version with cooling capability around the entire nozzle using a full circle air duct. I had some issues with the...

<p>Tired of finding the hole you can't see when the bed is in the way? You want this. ...It's not pretty, but it's dead on and works.</p>

I leveled my bed to perfection, carefully measuring the precise height required to ensure a flawless print. What caught me off guard was discovering that all four corners were spot on, identical in height - a rare occurrence indeed! If you're...

I enlarged the mounting holes to accommodate an M5 cap head screw.

Remixed to be able to print in two pieces and glued or bolted together. ...Second mount added on the front panel for another 40mm fan.

Shortened version of https://www.thingiverse.com/thing:3020026 (can't get it to link!) Made so it can still sit on the inside of the frame as I have a wall behind. ... Adjusted to print on side with minimal support.

for SKR2

I designed this case to move the Original screen outside the enclosure to make room for an SKR E3 Turbo mainboard. ...I used on the inside a mount from Thingiverse https://www.thingiverse.com/thing:4676133

I remixed the Bed Rod Holder to allow attachment from the bottom of the extrusion, instead of the side. This allows for additional clearance for a left mounted probe on a long hotend like a volcano. ... I now only need 2.5mm of clearance to avoid...

Plugs directly into an unused SD card slot found on a standard 12864 case design, similar to one described by TH3D in their 12864 conversion setup.

<p>The shorter the bowden tube, the better, right?</p><p>This mod allowed me to shorten the Tube by 17cm to 43cm. But measure yourself, as it is depending on your hotend and extruder.&nbsp;</p><p>The arm also damps the vibrations of the extruder...

Made a split version SO I didnt have to disengage the motor etc. Debranded . ...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

3 changes from the original: 1. Remixed to fit the SKR 2 board 2. Combined two formats to allow for mounting the Creality or TH3D Mosfet on the same box 3. ...Added optional zip tie brackets for cable management

Wanted to put my BigTreeTech SKR 2 board in the middle of the open space to have access to all sides of the inputs, including the USB port for a Raspberry Pi running Klipper, but Kersey Fabrication's mount pressed the inputs up against the case, so...

dimensions are 14 by 14 by 4.1, might need to try 4.15 or 4.2, 4.1 was enough to fix my issue which was a clicking noise inside dimension is close to 12

Hardware needed: -M8 tap -M8 bolt -608 bearing

I used self adhesive strip LED lighting on the inside of my e5+ frame and needed to diffuse the light. The clips are offset to clear the Y wheels so they don't get in the way and sit above the bed height, to avoid collision. I would advise 3 clips...

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

A remix from @bamcdo. I just changed the size of the holes down to 3mm which I used M3 screws to put through tightly and can use any sized washer >3mm in diameter. The original remix from bamcdo, the holes were just too big that I didn't have any...

I liked this design, but wanted to use it with an E3D Volcano and an EZABL Pro. The Volcano will mount directly to the BMG. I also moved the location of the hotend fan to be higher. I added an EZABL mount to the left side.Lastly, I cut away the...

This is a custom cable holder designed specifically for E-axis cables. Its sleek and compact design makes it an ideal accessory for any 3D printer setup. Inspired by the innovative design found at Thingiverse, this holder provides a secure and...

This is spacer for filament sensor to use with dual gear extruder. ...This spacer will align sensor exit with extruder inlet.

https://www.thingiverse.com/thing:4441076

https://www.thingiverse.com/thing:4441076

A simple tool holder to hold the wrenches, hex wrenches, scraper, cutter, and screwdriver that come with the printer Mounting requires: - 2x M4x10mm or M4x12mm bolts - 2x M4 T-Nuts - M5 will also work, but you will need to expand the...

The maker community's most trusted source for 3D models is now offering an updated design for the popular Ender-5 3D printer. This revised model takes into account recent modifications to the original design, ensuring a seamless upgrade experience...

Simplified Ender Model 5 Created as Chamber Design Base I designed it specifically for chamber design applications and made sure to include all key dimensions with an accuracy of 1mm. Perhaps someone can utilize these specifications. To access the...

This is a cable guide I designed to hold the Hot End cables up and out of the way. ...Eliminating the cable sag that sometimes would sit on the bed and interfere with the print head.

This will add a second independent X tool head to your existing Ender 5+ Hardware requirements 2x 450 mm mgm12 linear rails 1x 500 mm lin mgm12 linear rail 2 5015 Blower Fans 1 G2 timing belt Several different sized Hex metric nuts from m2 -m5. ...