exoslide ender 5 plus 3d models

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655) This version has a 9mm Y offset to be compatible with HeroMe Gen 5

... Use hex pattern or triangles infill. Wall line count (perimeter) 5 Concentric bottom and top pattern looks better ;-) I also designed a kind of support for the Stepper, if it gets to hot, to prevent bending in case of too high belt tension.

Spool Holder Parts Required: qty 1 - 3/8" x 5" Bolt qty 1 - 3/8" Nut qty 6 - #6-32 x 1/2" Socket Head Cap Screws qty 2 - 3/8 ID x 7/8 OD x 9/32 width Pre-Lubricated Bearing (I use these because I always have some on hand)...

Basic screw on X-axis motor strain relief. ... Print horizontal and you'll need M3 screw + nut.

This is a motor mount designed to mimic the stock motor mount with the lower section where the filament runout sensor would be removed. I used this mount while working with the 3DChameleon MK2 as I needed a way to mount two motors side by side...

Led Light Bar für Led Streifen 8mm. ...Befästigung der Led Streifen zusätzlich mit Kabelbinder möglich.

<p>I use a Lerdge board on this and wanted to have dual Z axis endstops to keep my bed level.&nbsp;<br><br>You will need:</p><p>2 brackets<br>4 x M2*12mm socket cap or button cap screws</p><p>4 x M2 nuts</p><p>4 x M4*10mm button cap screws</p><p>4 x...

I noticed that the original wire clip design was prone to popping out of the extrusions whenever someone merely touched them by accident. To address this issue, I modified the rounded ends of the clip that fits into the 2020 extrusions and gave them...

0.2 layer height supports: yes mounts to back of lcd screen with stock bolts make sure you replace the ground fork

A basic table to hold the Sunlu Filament Drier under your print bed and off to the side so you can dry while you print!

resized the 5mm bore holes down to 3mm

This is a remix, taken from two of Hangtight's designs, the one linked and this one https://www.thingiverse.com/thing:3241793 and modified to fit this bracket for top mounted linear rails: ...

Installed different lead screw bushing and changed my bed to the Wham Bam system so the original version was too tall and would crash the bed into this. I redesigned this to be a press fit and connect to the underside of the 20x40 that mounts to the...

I made it almost 1 to 1 with small changes. it works since the replacement perfectly. ... Be sure to print it with 4 lines for the wall and 50% infill for a longer lifetime.

I made an error in the BLTouch bracket height. If you have already printed V1, my apologies for the wasted time and filament. A few mods; all of the hard work had already been done: - I raised the filament sensor so as to clear the Hemera...

No supports, adjustable head angle, two M3x20 Feel free to support me with DOGE ;) DSmeW6UgGQEGP4gbfWfYAeP6aX3U1yhGju

for SKR2

I designed this to ensure that there is no pulling and twisting forces on the bowden tube, this ultimately ensures that there is less wear and tear on the bowden tube over time. I got this idea because I saw the bowden tube twisting during...

A human requires an additional module to be installed.

Designed to support the heat bed cables to help take some of the strain from the solder joints of the cables when bed is at the high positions. Undo the 4 pcs m4 screws holding the linear guide bearing, slide it between the guide bearing and...

This is a mounting plate to put the BTT TFT70 on the lower right front corner of the machine. I got fed up with not having a place to put it, so this solves my issue. I printed in PLA for the draft that you see in the photo, but you may want to...

To connect 2 PFTE to sensor. ... Update - now right scale.

I modified these 2 items and remixed it to fit the back rail without needing any additional tools.

The carriage wheel spacers now fit through the part for a more secure location. A support tube now keeps the Bowden tube from flopping over to one side. I didn't like how the corrugated tube was bundling cables with the Bowden tube, so I removed...

I've adapted the style of belt tensioners on my Y-axis by shortening the inner arms, allowing them to press firmly against the front horizontal extrusion. Having successfully implemented this modification, I was pleased with the outcome. However,...

Support for the cable from the bed to the controller.

This is not a remix of but was directly influenced by this Thing: https://www.thingiverse.com/thing:3836394. The retractable badge holder is an ingenious concept that I wouldn't have come up with on my own. It keeps your cables from sagging and...

<p>Parts Required: (I used Socket Head Cap Screws)<br>qty 6 to 10 - M3 x 6mm screws&nbsp;<br>qty 2 -M5 x 8mm screws and T-nuts<br>qty 2 -M3 x 8mm screws and T-nuts</p><p>You might need to move the bundle holder up a hole to clear the end stop</p>

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

Added some support to keep it from warping so I can use PLA+. tweaked it a little so it lines up with my nozzle better. Been using it for a week now and it looks solid. ...Remember to check "print thin walls" in Cura