exoslide ender 5 plus 3d models

CREALITY ENDER 5 PLUS SPOOL HOLDER CENTERED BRACKET EASY TO PRINT As my Ender 5 Plus arrived, I found the spool holder fixing needed improvement. You may also notice that I've used my "Creality Ender 3 5 Pro Plus Universal Ball Bearing Super Easy...

Ender 5 Plus run out sensor bracket for dual drive extruder (BMG type).Bracket places run out sensor at correct offset for use with dual drive extruder like the BMG.Adds filament guide.Link to Ender 5 Plus firmware config and cable management photos....

Because the metal dual gear extruder for creality Ender 5 Plus has a different entry path for the filament then the plastic extruder, a spacer is needed.

Ender 5 Plus Stock X Carriage Plate - Hero Me 7.2 Bolts directly to it This file was created by the Great Work of: bametalman

This is the X Endstop Version for the Ender 5 Plus with the Micro Swiss Direct Extruder Plate mounted on Linear Rail's.

This is a remix of Hero Plus ver6 OEM and MicroSwiss with BLTouch created by mediaman adapted to Creality Ender 5 stock hot-end plate. ... Base STL: Hero_Plus_OEM-Micro_Swiss_Adj._BLTouch_ver6.stl can be found here.

I printed this clever component for upgrading my Ender 5 Plus to the Bigtreetech SKR 1.4 and a Raspberry Pi: https://www.thingiverse.com/thing:4328907 Unfortunately, the Mosfet of my Ender 5 Plus has a slightly unique configuration. ...That's why I...

Chain mounts and bl touch mount for ender 5 plus + microswiss direct drive After adding the Hero Me Gen5 to my ender 5 plus I didn't have a bracket that fit my bl touch and I wanted cable chains so I made mounts for them.

This is a bracket for the Ender 5 Plus to hold the Meanwell 600W SE-600-24 in the Ender 5 plus's stock housing. This can be done with slight lengthening to some power wires. ...There are two stl's attatched, one designed to be drilled for 4mm inserts...

This will be fixed in an future version.Edit (3.5.2024 Hotfix!) :Due to some weird measurements, the adapter didn't fit, because of the screws of the mounting plate of the Ender 5 Plus.Edit (2.5.2024) :Unfortunately, I had a very busy time last...

At https://www.thingiverse.com/thing:4821969 jerryfudd designed a Ender 5 Plus Power Supply Casing Noctua 92x14mm RSP-500-24. ...I made this remix so that the openings fits for the new Noctua fan.

remix of hangtights fantastic design. ...remixed the base so it fits the ender 5 plus. ...without this base the bl touch is not able to be mounted and the base plate wont fit the carriage.

https://www.thingiverse.com/thing:4141056 and https://www.thingiverse.com/thing:4738723 I needed to have something that would fit the "Ender 5 Plus" that: 1) Would hold the bowden tube 2) Account for the extra spacing needed for the BLTouch Bracket...

I found the standard cooling shroud on my Ender 5 Pro and Ender 5 Plus to be a little inadequate. I couldn't find a model on Thingiverse that seemed to match my printers, both of which have Microswiss direct drive extruders. ... This is a simple...

... sensor holder to the Micro Swiss Direct Drive mounted on linear rail carriage. ... You will need to follow instructions on [Ender 5 Plus Linear Rail Conversion](https://www.thingiverse.com/thing:4578889) so that your limit switches are setup correctly

Unable to find anyone else who had successfully installed ExoSlides on their Tronxy X5S, I'm hoping these designs will be useful for others. The design is quite rough and lacks mounting holes. On the design itself, I simply drilled out the necessary...

Minimal support is needed.Ender 5 Plus - Print on the side opposite the PCBA connector opening. These models are tailored to Ender 5/Pro/Plus which have been converted to the ZeroG Mercury One CoreXY system.Ender 5/Pro version mounts to the rear...

... housing that comes with the Ender 5-Plus. This can probably work on other creality machines that use the same filament sensor housing/microswitch as the Ender 5-Plus You might need to hot glue the PTFE tube to the housing so it doesn't move around

... correctly, this design incorporates a filament guide. For those interested in implementing this design on their Ender 5 Plus, you can find firmware configuration and cable management setup guides here: https://www.thingiverse.com/thing:4544301

Purpose: - Very Simple Adapter for Fitting the Meanwell RSP-500-24 into the Ender 5 Plus Case - Included Blanking Plate for Voltage Selector Notes: - 4x M4x4mm Button Head Bolts for Case Fixing - 4x M5x5mm Countersunk Hex Bolts for PSU Fixing -...

Cable strain relief for Stockman59's Hero Me Gen5 mod for the ender 5 plus with Microswiss DD. Use M3 x 8 or 10mm, not sure which ones fit. Has 2 slots for small cable ties to thread through. ...Print on its back (so the curved surface where the cables...

I combined two sections of the renowned Hydra fan duct from Thingiverse (https://www.thingiverse.com/thing:4062242) with an BL Touch template from Thingiverse (https://www.thingiverse.com/thing:3978365), allowing me to maintain the Ender 5 Plus's...

... a way to mount the filament dryer to my printer due to limited space. ...This designed seemed the best for my setup on an Ender 5 Plus. ...So remixed it to attach onto the rear 2040 extrusion Uses 4 M5 x 10 bolts with tnuts to attach to the frame.

Modded for Microswiss and ENDER 5 Plus I took parts that i liked and printed and modded them to suit how i wanted them to work and printed them again. Satisfied with how they came out but added a support triangle to the BLTouch Mount as i felt this...

The support for Dahua Consumer Camera I've designet for my Ender 5 Plus. 20cm high simple to redesign in TinkerCAD. Also in the package there is holder very similiar to original holder if you lost yours. ... Added more rigid v2

This is a Remix of a Cable Support for the Ender 5 Plus. But i didnt find that Thing again on Thingi. I just made the space between the holder bigger so it fits with the original BL-Touch Plate. ... You have to ad support to the holder but not to the...

Purpose: - Very Simple Adapter for Fitting the Meanwell RSP-500-24 into the Ender 5 Plus Case - Included Blanking Plate for Voltage Selector Notes: - 4x M4x4mm Button Head Bolts for Case Fixing - 4x M5x5mm Countersunk Hex Bolts for PSU Fixing -...

This is a board mount for the large ender 5 Plus case for the BTT SKR 1.4 or SKR 2.0 mainboard + the BTT UPS board. Slot fit over existing mount holes and use existing screws. ... Please see updated version to include Raspberry Pi: -...

This a no extra / different screws required print to mount your Big Tree Tech touch screen to your ender 5 plus. Both objects are all in one file. It includes the mount and adapter. ...Some clean up will be required depending on how your printer is set...

Made this to mount 7" Pi screen to my Ender 5 Plus.Should work in any extrusion with adequate space.Made for use with Pi Screen Case https://www.printables.com/model/237957-raspberry-pi-7-touch-screen-display-lcd-tft-case-e4x M3 bolts4x M4 bolts4x M4...