exoslide ender 5 plus 3d models

Cross bar braces for the Creality Ender 5 Plus to stiffen up the frame a bit and lessen the top wobble caused by X and Y axis movement. It reduced the visible wobble quite a lot on my printer. Use any 8mm rod cut to 670mm +/- 5mm for the left...

I have upgraded my Ender 5 Plus to a Dual Extruder setup with the Chimera 2in-2out hotend, taking on several requests for files and instructions. Here is my attempt at providing some guidance. Most of these parts are modified versions of something...

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...

This was the crossbar relocation brackets that stood out to me the most, so I remixed it for the 5 Plus and it works perfectly. The only hitch was not being able to utilize the original tapped holes on one side of the frame - specifically on the 2020...

This is a combination of the Parts from paydayxray (https://www.thingiverse.com/thing:4310609) and Andrea_Botti (https://www.thingiverse.com/thing:4710174) https://youtu.be/n-ky2i-Otvw Ich wollte einen Direkt-Extruder für meinen Ender 5 bauen. Das...

You may think that it's not Ender 5+ any more, but almost everything from the original kit is reused with minimal adjustments.That was the design intention:- no hassle with electronics: 100% ender5+- sturdy frame: I use locally available "Kombi...

Just needed a measuring stick holder for my Ender 5 Pro. The hole is 20mm x 6mm. Should fit for the most types and fits very tight on the 20mm side of the profile. ... I add the Fusion360 file as well.

Just needed a measuring stick holder for my Ender 5 Pro. The hole is 20mm x 6mm. Should fit for the most types and fits very tight on the 20mm side of the profile. ... I add the Fusion360 file as well.

Due to the Ender 5 Plus's independent Z screws, they can easily get out of sync, making it a challenge to maintain proper alignment. Removing any part can cause the bed to fall and become misaligned. If you're like me and don't run auto-bed leveling...

---------------------------------------------------- This is my design for a kinematic self levelling bed system for the Ender 5 plus. This design allows you to fully automate the levelling of your bed to a very high precision - meaning you only...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus.NotesRecommended parts have “rev4” present (except for the buttons).  Alternatve parts (refer to “Earlier Revision Options” above) have "rev2" or "rev3"...

This is a complete overhaul of the ender 5 plus's gantry. After trying the Merc One core-xy mod, I found that the belts were far too long to prevent ringing, and the belt path too complex to avoid problems. Also, the stock belt arrangement really...

I needed led strip holder for my Ender printer.

I tried using the original design on my Ender 5+, but unfortunately, the tabs for the screws were slightly too thick. Printing it with resin proved to be a challenge as well - the logo required extensive support structures, which made the process...

... for heavy and expensive devices. Use an M4 x 25mm (or longer) screw and nut to mount it to the cornerpiece of your Ender 5 rack. For your camera, simply add the right screw (e.g., check this one: https://www.thingiverse.com/thing:595837). ...

So I started Freecad and adapted the template to my needs. This is a combination of the Parts from paydayxray (https://www.thingiverse.com/thing:4310609) and Andrea_Botti (https://www.thingiverse.com/thing:4710174) Ich wollte einen...

You may think that it's not Ender 5+ any more, but almost everything from the original kit is reused with minimal adjustments.That was the design intention:- no hassle with electronics: 100% ender5+- sturdy frame: I use locally available "Kombi...

This is a linear rail mod for the Ender 5 Plus. It encompasses the XY&amp;Z axis. I designed these parts because I was unhappy with most other mod variations of them.</p><p>Z Axis - The Z axis part were designed using the BLV MGN Cube as a starting...

This is a Creality Ender 5 Hot Bed Cable Relief that I Remixed in TinkerCAD. I took the zip tie design and designed an attachment around it. The reason I designed it is because a lot of the other designs took way too long to print and took extra...

Just added a side car for the BL touch since I imagine that most people have the BL touch as it came stock with the ender 5+. I printed the adapter in PLA, but you may want to go with PETG as it sits really close to the hot end, so we'll see how...

Prolunga per sensore filo di crality ender 5 plus.

Plate to mount a Biqu H2 to the Ender 5+ Old nozzle to New Pictured above Nozzle to Probe -33,-11, Z should be same as stock mounts using 2 M3 x 8mm botls for the H2 and 2 M3x 8mm bolts (may want use a washer) and 2 m3 nuts for the Bl touch Bracket.

This is a linear rail conversion for the Ender 5 Plus. It encompasses the XY&Z axis. I designed these parts because I was unhappy with most other mod variations of them. <b>Z Axis -</b> The Z axis parts were designed using the BLV MGN Cube as a...

This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't...

The original part designed be Xerber https://www.thingiverse.com/thing:4727217 did not work with my Ender 5+, my Z rails are an extruded aluminum design and have an extra bit on the edge, instead of the flat bars pictured on the original design. ...

... you were homing your z axis then you need to re-level your bed carriage. This will help with that. This spacer is long enough that the stock Ender 5 + hotend will not be able to touch the bed when you tighten the z axis, so no fear of it crashing.

Dual Gear Extruder: This design was specifically developed for: https://www.amazon.com/WINSINN-Extruder-Creality-Upgraded-Aluminum/dp/B07SY745CF/ref=sr_1_2?dchild=1&keywords=dual+gear+extruder+ender+5&qid=1590272315&sr=8-2 This mount securely...

... If you like my Design please give me a like or a make. Thank you Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0,12 Infill: 99 Filament: CR-3D PLA Gold Category: 3D Printer Parts

Also, I don't know if this would work on the normal ender 5. I don't have one so I can't test it, but it should fit so maybe. Parts list: 2x 60T-20T closed loop GT2 belt and pullies, 5mm bore 2x 20T GT2 Pully, 5mm bore 6x 20T GT2 Pully idlers,...