exoslide ender 5 plus 3d models

Mounting plate adapter to use microswiss direct drive plate with the exoslide system To mount remove exoslide, mount plate to exoslide then mount plate to microswiss plate then mount exoslide back on rail

This is a modified setup from the original assembly to accommodate the addition of the stock Ender 5 Plus BL Touch.

ebder 5 plus microswiss mount setup. 3 screws mounting. you need 2xm4x60 2m20x4 and one screw and nut from an original roller wheel. this braket is used to be mounted under the cariage. each exoslide on the y axe must be mounted as shown with...

I needed a mount for my TH3D EZABL and and wire loom support to help with that giant loom the Ender 5 Plus is doomed with. Its not perfect as the fit and finish is off (Chamfer) on a couple spots that I couldn't figure out. I included the STEP file...

Ender 5 Plus Exoslide Marlin Code Mod Infill = 100% NOTE for this Mod the Front Bar needs to be moved DOWN also the Exoslide is on the front screws on the X axis bar which the instructions say use the back screws Z offset changes depending on nozzle...

This is a remix of someone else's design that I modified to work with the exoslide system. ...Drops the front bar by around 100mm.

I built an enclosure around my Ender 5 Plus. After do that I placed my Spools in a Zip Lock container (with Filament drier inside) on top of the case. Then, I just routed the filament from the Container through the top of the Case with Capricorn...

However, please note that I've only tested this particular setup on the Ender 5 Plus machine with HMG5 fan ducts, so your mileage may vary if you decide to use this remix with a different system. The Exoslide Direct Drive mount caused my extruder to...

It is specifically designed to fit an Ender 5+ with 4020 hotend fan, Micro Swiss hotend, and the ExoSlide gantry upgrade. Not sure if anyone else out there has that setup, same as me, but if not, you might be able to mod my mod for yourself... ...

This mount is specifically designed for the Winnsinn Dual Gear Extruder in a direct drive configuration. To ensure seamless installation, I highly recommend extending all screws to their maximum length available, as this will provide optimal...

Smooth Fang Mounting Plate - Ender 5 Plus - Micro Swiss Direct Drive - BLTouch - ExoSlide BLTouch Approximate Offsets = X-44.6, Y-6.6 Ender 5 Plus (with BLTouch probe), using a Micro Swiss Direct Drive extruder kit, mounted to an ExoSlide linear...

Designed this Biqu H2 mount for exoslide motion system, installed on my ender 5 plus Walls 4 and infill 40%

Adapter plate to allow you to mount your filament sensor plate sideways on your exoslide to allow for side loading

Here's a re-designed direct drive mount, compatible with Exoslide linear rail products on the Ender 5/5+. Originally made of PLA, this design was prone to bending and deformation due to heat and weight. To counteract these issues, I've added extra...

This innovative design addresses a major issue with existing Exoslide mounts, making it easier to achieve smooth and precise printing on your Ender 5. Specifically crafted for the Exoslide v1 without an upper plate, this mount ensures optimal...

I purchased the Version 3 Exolide Kit specifically designed for the Ender 5, only to discover that the extruder alignment was woefully off by approximately 9.5mm. Undeterred, I made the necessary adjustments and successfully calibrated my printer.

Ender 5 plus bin

8 - M4x10 countersunk screws 2 - Exoslide belt brackets ( https://www.exoslide.com/products/hardware/bracket-belts-kit ) 1- Pack of belt clamps ( https://www.exoslide.com/products/hardware/belt-clip-gt2) UPDATE 8/8/2021 I am adjusting the top/bottom...

perfect fit to ender 5 plus V2 https://cults3d.com/en/3d-model/tool/ender-5-plus-drawer-v2

This is a Cable Holder desigend for the Ender 5 Plus.

Creality Ender 5 Plus model. ...Currently a work in progress and will be updated as I work on it Many parts derived from this model: https://grabcad.com/library/creality-ender-5-pro-1 Last updated 8/10/20

Enclosure for a Ender 5 Plus, work in progress, will update as I get more completed.Material is 2mm Aluminum, if needed I can upload the DXF flats.

This is a model I created of the Creality Ender 5 Plus. ...I use this to design add-on parts and enclosures.

This is a design for a bed levelling on an Ender 5 Plus 350mm x 350mm bed. The design has a height of 2mm. ... I have a complete bed levelling guide here - https://mattharmer.me/correctly-level-a-creality-ender-5-with-bl-touch

Hintergrundbild für Euren Ender 5 Plus.1.Datei in Cura einfügen (Programm nicht öffnen)( C:\Program Files\UltiMaker Cura 5.3.0-beta.2\share\cura\resources\meshes)2.Befehl im Ordner definitions in der Ender 5 Plus Datei hinzufügen und speichern.(...

I made a toolbox for the ender 5 plus. My tools where everywere so i hope you can use this as well. You have drawer for extra space. and on top for all the tools. ...You also have space for aech spear nozzel from 0.2 to 0.8.

This is a modified version of this fanduct: https://www.thingiverse.com/thing:3020267 I have adapted it to the Ender 5 plus. The belt holders collide with the original on the 5 plus, so I've made space for this. Furthermore, I created a little more...

Shout out to [zanek012](https://www.thingiverse.com/zanek012) for creating the files in SolidWorks [Creality Ender 5 Plus](https://www.thingiverse.com/thing:4556594/) files. I took these files and converted them using Rhino 6 into STL files and...

Some parts I did for enhancing my Ender-5 Plus when doing the direct drive upgrade.Cable guideA fixation for the extruder cables. Needs a M3 x 6 counter sunk screw.</p><p><strong>Z-screw fixation</strong></p><p>The Z-screw holders need four M4 * 10...

Riser legs/feet for my Ender 5 Plus are designed to work seamlessly without any modifications to the printer. They incorporate a 2020 extrusion keyway that locks into place within the E5+ frame, and a recessed hole at the bottom allows for easy use...