evga 3080 ftw3 support bracket 3d models

To assemble this custom support bracket, you will need the following components: * 1x NZXT H700 GPU Support Bracket * 2x NZXT H700 GPU Support Bracket Backside * 2x 10mm m3 screws * 2x m3 hexagonal nuts For optimal results, I recommend printing this...

... hole for enhanced grip. Printed without support, it was created using specific print settings. Print Settings: Printer Brand: MakerBot Printer: MakerBot Replicator Z18 Rafts: Yes Supports: No Resolution: Standard Infill: 60% Notes: Three shells

This is a custom bracket support designed for the Wanhao I3 printer's sagging prints, specifically intended for use with the original bracket that comes supplied. Its design ensures it remains thin enough to reuse the original screws. ... Print...

;) This has 3 thing files: -90 Degree Bracket (most common) -30 Degree Top Bracket (for high side stair railing) -30 Degree Bottom Bracket (for low side stair railing) For stair railing, you will need one top and one bottom for each 2x4! For...

Two of these brackets mounted on the side boards will support an axle capable of holding 5kg of filament. Instructions Print with plenty of infill to make it strong enough to support the weight. Position the bracket on the board as far back as it...

... delicate as I sized them to fit the original design. Be careful when removing the support bracket from the bed, removing supports, and inserting the RPi case into the bracket. Printed at 0.2mm with supports due to the flange overhang. ... Enjoy!

... a few months. ... This small support piece slips in from underneath (tight fit) and the PCB will stay straight forever. ... If your PCB has already bend down a bit, simply lift it a tiny bit by pushing upwards on your graphics card from underneath.

Bracket designed to support heavy PCIe or PCI cards when using them in a bare motherboard on the desktop.Modern cards seem to use a bit thinner metal, the dimensioning of the slots is a balance between too tight fit on older PCI cards and too loose...

A replacement plate for the EVGA Z15 Metal Logo. It does not screw in like the stock Z15. I suggest using whichever glue you like (I used CA glue for mine). Add your own branding to the top plate for your own personal flair. ... I printed this on an...

connect LX-16A motor bracket to your tool.

The vertical GPU riser bracket from Fractal started to slightly bend after a few months. This small support piece slips in from underneath (tight fit) and the PCB will stay straight forever. If your PCB has already bend down a bit, simply lift it a...

Someone needs to add a few angle brackets to secure the bottom of a cabinet. ...Both sides of the bracket are exactly 8 millimeters in length, while the bracket itself measures 15 millimeters across.

This is a bracket i designed to keep the gantry more stable on my Anet A8 for the other side just mirror the bracket in the slicing program.

The cover will conceal the EVGA logo and serve as a housing for two RGB strips that will illuminate a new, futuristic logo. Note: The design is still in its early stages, so it's not yet ready for printing. ...Unfortunately, my printer is currently out...

Support bracket for the MK3 with the new Delta PSU. This is used when removing the PSU to make an enclosure for printing things like ABS. (Power supplies don't appreciate the heat like ABS filament does!) Print instructionsSuggested Settings Slic3r...

This bracket allows you to remove the large heavy metal bracket found in the Amiga 2000 and replace it with a lightweight bracket to keep it somewhat secured to the motherboard and case. I would advise you put a thin foam backing on the bottom parts...

Inspired by this GPU support but the designs are so different I didn't end up calling this a remix.This is a GPU support bracket for an NZXT H700i or NZXT H700 case. It fits my GTX 1080ti Founders Edition, which means it should also fit a GTX 1080...

This is a USB-C port used to convert an EVGA Z15 keyboard to USB-C. It pops right in but I suggest adding a little bit of your glue of choice to secure it (I used CA glue). The USB-C board it was designed to fit can be found on amazon under...

You'll need nine bolts and nuts per bottom bracket, and three nuts and bolts per top bracket. Luckily, my delta printer came with extra hardware, so I didn't have to buy any extras. ... One of the brackets has a compartment that you can use to stash...

I was worried the lower tab would snap off with a heavy server so I remade the bracket with a thicker bottom end.

... towards the controller board. ...I opted to replace the X motor mount screws with slightly longer ones leftover from construction, which helps account for the added thickness of the bracket. ...The package includes .STL and Inventor Fusion files.

To fix my broken filament tube holders at the rear of my Replicator, I found Thingiverse designs that required original holders, so I designed an innovative "all-in-one" replacement bracket. ...Print it, remove the old holders, attach the new bracket...

Here's a bracket that can be screwed down into the table that a Onefinity CNC sits on and be used to clamp on a cardboard guard to shield the y-rails from chips and dust.

Two sets of brackets attached to the side panels will bear the weight of a sturdy axle that can sustain a payload of up to five kilograms of filament.

... a 3mm x 25mm screw to the Replicator's rear. An update on September 12, 2012, involved trimming the bracket's top to prevent rubbing when loading a second spool of filament. ...Additionally, a new hole for a wood screw was added below the cord.

... I decided to design an all-in-one bracket. After printing this new part, I removed the old tube holders from the Replicator's back, installed the bracket in their place, and secured it with a few zip ties - now everything is working smoothly again!

Relocating my enclosure build forced me to search for a bracket that could accommodate a new power supply unit. Unfortunately, all of the existing brackets were designed for an older style PSU. When attaching this stand, you will need to replace the...

Curtain rod holder with support

The original bracket holding the rafter broke: the small part fixing the main bracket. The STL is the small part only, see the photo of the original spare part. The first one I printed from PLA worked for 1 year, re-printed a new one with PETG with...

The original design was too thick and i want a minimal design, so i remixed and here there are the modification: -The thickness of the bracket was reduced from 20mm to 10mm -Added a version of the bracket for 200x200 buildplate (Bracket_10mm_short)...