ev charging cable under garage door 3d models
329303 3d models found related to ev charging cable under garage door.
thingiverse
Stop garage door from smashing EV charge cable. Made for Tesla Mobile charge cable of approx. 13mm diameter. Should work with cable up to 15mm as opening is 16mm wide. Its 22mm tall and 35mm wide and matches my garage door at 55mm thick. There's...
thingiverse
If you have an electric vehicle charging station installed in your garage but prefer to park outside, then you'll need to run the charging cable under the garage door. This action can crush the charging cable, causing damage to its casing or even a...
thingiverse
I designed this fitting so as to pass the charge cable for my EV under the garage door (the charger is in the garage, the car parked on the drive). Cutting a channel in the garage floor and passing the cable through this fitting provides a permanent...
thingiverse
Designed so that I can pass my Tesla charger cable under the garage door without fear of it getting damaged. Now updated with RH and LH versions (orientation looking outside from garage door).The wedge shape allows the door to still seal and not...
thingiverse
An EV Charging Cable Guide - Help keep your electric vehicle charging cable in place.
thingiverse
I was tired of my EV cable unravelling, so I designed a thingy™ to keep it in place!Designed around a VW cable, 10.2mm diameter.
grabcad
Most public charging stations are equipped with a type 2 socket. ...All mode 3 charging cables can be used with this, and electric cars can be charged with both Ac Abd Dc
grabcad
Most public charging stations are equipped with a type 2 socket. ...All mode 3 charging cables can be used with this, and electric cars can be charged with both Ac Abd Dc
thingiverse
This comes in handy for those that would like to clean the charging cables of their electric vehicle. Once printed, add pieces of kitchen flat sponge, the scrubbing layer/side holding them in place. I used 2 Scotch Brite green flat laminate sponges...
thingiverse
My concern was also to have an opening in the garage door that isolate for cold air when the cable is going through that hole This composed of three part 1) the chassis that hold the cable hole 2) the flap that close the hole when there is no cable...
thingiverse
No more cable on the ground in the winter :)Remix from aproemel "EV cable wall mount".Modified so that I can pass it throught my galvanized garage frame.Diameter hole of 27mm.So far so good, will update on the strength of it.
prusaprinters
I designed this to hold my Garage door opener in my BoltEV.
thingiverse
Wallbox for Telewell EV TYPE 2 charging cable. ...The cable converts 3x16A CEE -plug to TYPE 2 EV -plug. This wallbox keeps the control electronics on the wall making the cable a kind of EV charging station.
thingiverse
When the torsion spring broke, the cable was released from the garage door bottom bracket on the side without the thimble. The cable without the thimble was curled up. In contrast, the cable with the thimble stayed in place and remained straight...
thingiverse
Holder for EV charging cable type 2. Holds the cable flush to the wall instead of sticking out. ...One file for left and one for right side orientation
thingiverse
Help open the charge door when it´s froozen. ... Printed wtth TPU NinjaFlex
thingiverse
Help open the charge door when it´s froozen. ... Printed wtth TPU NinjaFlex
prusaprinters
I will also upload a version for recessed screws and one with a cable organizer.Prints with most filaments and resolutions.
thingiverse
This is a simple passthrough that will protect your EVSE charging cable from the weight of the garage door if your EVSE is located inside of your garage and the vehicle is in the driveway. The current model will fit a cable that is up to 20mm in...
thingiverse
Protects your Level 1 EV charge cable if you have to close your garage door on it. Prevents cord from being pinched by garage door. Allows cord to slide freely (just barely) while door is closed on top of it. Should fit most/all Level 1 charge...
thingiverse
Plug and cable hanger for type 2 EV charging cable. Model can be easily adjusted for different weatherboard angles. The plug is released by gently lifting the handle slightly before pulling out. The angle of the socket matches that of an Evnex wall...
thingiverse
Made specifically for holding the charge cable of my Tesla EV, I designed this holder to be printed with ease. After printing, however, I still need to test its functionality. The sliding mechanism that conceals the screws is surprisingly tight, but...
thingiverse
CSL17A0272 - Mennekes Typ 2 Charging Cable, smaler Grip, as seen in pictures: scale down to x/y 80% for use with Version 2: still best fit on Mennekes Typ 2 Cabel, but should fit better on other cables as well, try printing in TPU - V2.0 - larger...
thingiverse
Re-engineered holder for Type2 charging cables, created from ground up as original model was inaccessible. ...Printed at 0.2mm resolution without requiring any customizations.
thingiverse
I then cut 2x4's to fill the rest of the width, painted them black to blend better, then closed the garage door onto the setup - I did have to be quick to pull the release cable on the garage door so it wouldn't reverse back up after it sensed the 1...