eufy spaceview crib mount 3d models

To overcome this challenge, I created a clamp-mount bracket that angles the Spaceview downward by 25 degrees, allowing for an unobstructed view into the crib. I would like to extend my gratitude to several Thingiverse community members who provided...

45° Wall mount for eufy Spaceview baby monitor. I'm using Tesa Power strips to attach it to the wall. ...That way it can be removed without damaging the paint and I can also use it in holiday homes.

This is a simple mount to attach a Eufy babycam to a tripod. You just need to glue a 1/4"-20 nut in the bottom hole.I printed mine with 20mm layer height and PETG. ...Should work with PLA as well.If you like what I'm doing……consider buying me a ☕ on...

A mount for the Eufy SpaceView baby monitor camera. The mount has an arm with a screw clamp allowing the camera to be clamped and mounted to, for example, a nearby shelf or ledge. The mount holds the camera at a 20 degree angle giving a better...

This is an adapter to attach a Eufy Spaceview baby monitor to the [Modular Mounting System](https://www.thingiverse.com/thing:2194278). ...It is necessary to print it upside down (that is with the modular mount pieces facing upwards) using supports.

Eufy camera crib rail mount

Bracket for mounting the Eufy Spaceview baby monitor camera on a window handle. Simply slide onto the window handle from below and twist to lock. Should fit at most window handles. ...Hole diameter is 25mm, in which the window handle should fit...

SummaryThe adapter angles the Eufy Spaceview baby monitor downwards 45 degrees to eliminate blind spot under the wall adapter when installed upright (you can install the wall adapter upside down, but it can drop if it comes off of bracket). ...Smaller...

The adapter adjusts the Eufy Spaceview baby monitor downward by 45 degrees to eliminate blind spots under the wall adapter when installed upright, providing a stable installation. Although you can install the wall adapter upside down, it may detach...

I was in need of a holder that extends the Eufy Babyphone Spaceview outwards from our bed. I used the design of elcojacobs for the camera holder - very nice fit - and added the bed frame holder. It is a 23mm gap, so the holder sits snug on the bed...

The bottom plate fell off of my Eufy SpaceView camera so instead of buying a new camera I made a new wall bracket to around the base.It has 2 chamfered screw holes in the bottom so just mount the bracket and slide the camera into it. It's sized to be...

Material needed: 1 x 3mm*10mm screw 1 x 3mm hex nut (depends on you printed ground plate) Or just glue it together English: Here you can print a baby monitor holder for the Eufy Spaceview. You can clamp it to the baby bed. The range can be variable...

Mount a Eufy Solo IndoorCam C24 to a West Elm Mid-Century Crib for baby monitor.

Eufy Spaceview Baby Monitor Tripod Base, becase the connector that comes with the camera limits options. ...Highly inspired by Shinwachi

With holes to accommodate #8 screws.

This is a simple mount to attach a Euby babycam to a tripod. You just need to glue a 1/4"-20 nut in the bottom hole. I printed mine with 20mm layer height and PETG. ...Should work with PLA as well.

Wall-mount for Eufy Spacecam baby monitor. Allows a good angle for monitoring a crib below, or an entire room if placed high enough. ...Blocks blue LED light from shining on baby.

Wall-mount for Eufy Spacecam baby monitor. Allows a good angle for monitoring a crib below, or an entire room if placed high enough. ...Blocks blue LED light from shining on baby.

Print the model standing upwards (as exported in the stl) with support!I used regular white PLA with 2 walls and 10% infill.

This is a mount for Eufy Cam on the 4040 extrusions on an Ender 3 V2 (though i'm sure it would fit others as well)

Mount is made for an 80mm drainpipe. ...Can be fastened with a tyrap or something else up to 8mm wide. The standard Eufy mount can be connected to the mount with two M4 screws and nuts.

Rather than redesign the whole part, I decided that I would combine the 15º mounting bracket with and additional 25º wedge and get the 40º I wanted. Installation: 1. 2 nuts are recessed into the back of the 3D printed part 2. Attach the 3D...

This is for the Dual Camera doorbell:...

I needed a mount for my Eufy Cam2C that provided more angle when mounted from the ceiling. ...(https://us.eufylife.com/collections/battery-camera/products/t88311d1) &nbsp;</p><p>There are 2 stl files since I needed one that was taller to allow the...

Design Details: You can find this design on Tinkercad at https://www.tinkercad.com/things/9ufTBR3Bduj To learn more about Eufy's battery-powered doorbell, visit their product page at...

Needed to change my camera from it's place for a special occasion.. ... Due to the camera size, it was tricky so I was inspired by another source and made this with the Eufy screws.. fits perfectly. Printed, with PLA, 0.15 and no support. ...

Simply mount for attaching a Eufycam2 to the ceiling.

I had to create the mount to tilt the camera away from the brickwork and to adapt to the location of the existing doorbell wiring.

An essential wall attachment bracket designed specifically for securing the Eufy Spaceview Baby Monitor safely and firmly to any wall.