ethernet cable holder 3d models

Customized version of https://www.thingiverse.com/thing:2054634 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2054634

Customized version of https://www.thingiverse.com/thing:1543201 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1543201

This is a remix of the Framework expansion card holder by bradstopher99. ...One of the slots has been expanded to accommodate the Ethernet adapter sold by Framework.

Cat 5 Ethernet Wire Clip.

Ethernet Cable wall clips with screw mount X1 Created under the impression of https://www.thingiverse.com/thing:4164162 but for a single cable and stronger

If I'm being completely honest, I tend to clip my Ethernet cables when working at these makeshift desks, which are essentially just workbenches converted for office use.

This is a cable comb for Cat 5e Ethernet Cables.Looking for a Cat 6 variant of this model?<Click Here> ← To be updated   

24 Ethernet Cables Guided Directly to 24-Port Patch Panel. Hole Numbers Match Port Numbers for Easy Future Access. A Convenient Zip Tie Guide Surrounds the Entire Piece, Allowing Secure Cable Management. Two Guides Can Be Joined Together Using a...

This is a direct substitute for the well-known damaged Ethernet flap found on Lenovo Flex 2 laptops.

... board with UNO Shield Ethernet Shield W5100 /W5500 R3 expansion board and expansion boards with screws. ... Structure to unify our Arduino MEGA board with the UNO Shield Ethernet Shield W5100 /W5500 R3 expansion board and expansion boards with screws.

... board with UNO Shield Ethernet Shield W5100 /W5500 R3 expansion board and expansion boards with screws. ... Structure to unify our Arduino UNO board with the UNO Shield Ethernet Shield W5100 /W5500 R3 expansion board and expansion boards with screws.

I spotted an alternative Ethernet cable management setup and noticed its effectiveness relies heavily on being able to access both sides. However, my situation called for a different approach since I was running cables in the upper back corner of my...

A Clamp that can be mounted to the Left Hand Bumper that I designed to secure an ethernet lead. Diameter of lead is 6.5mm.It's sercure to the XR18 using two 4mm Capheads. These align with the orginal mounting holes. ...This is printed without supports...

Ethernet cable screw mount, suitable for Cat 5 to Cat 8 cables. It can be printed in a flat format or at an angle, with varying results depending on the printer being used. To achieve the best possible outcome, it's recommended to print the design at...

... and Holder P.S. ...Drawings from ESS can be a bit imprecise, but that's still accurate enough for use in projects like Holders Print Settings: Rafts: None Needed Supports: Essential Resolution: 0.1-0.2 Precision Achieved Infill: 50% Optimal Density

Simple 4 / 8 cable clip. ...Cables snap into place, and have a little wiggle room but shouldn't ever pop out. Made for my chunky Cat6 FTP cables, you may have to reduce the size a little bit for cheaper thin cables.

I like clips from chelsar with bigger hole for nails, but needed to tune it for a bit smaller cable diameter. I have 24AWG Cat5e cable with about 5mm in diameter. ... I also added the version for 2 cables in parallel.

... ...Convenient for CNC's and printers that utilize network cable for stepper leads. I employed this on my MPCNC. Usual cable width I used it for was 6 to 6.5mm diameter. The mounting holes fit #8 screws quite well. ...Constructed with a 4mm hole.

... the furniture itself only has a small cap between itself and the wall. To hide the nail, a small cover can be attached. It might be necessary to mirror it inside the slicer when the cable should not be mounted on the right side of the furniture.

It might be necessary to mirror it inside the slicer when the cable should not be mounted on the right side of the furniture. ...Print Settings Printer: Qidi X-MAX Rafts: Doesn't Matter Supports: No Resolution: 0.08mm Infill: 100% Filament: Geeetech...

It might be necessary to mirror it inside the slicer when the cable should not be mounted on the right side of the furniture. ...Print Settings Printer: Qidi X-MAX Rafts: Doesn't Matter Supports: No Resolution: 0.08mm Infill: 100% Filament: Geeetech...

After having purchased and used the full set from ChArlie_24 for my PC cables I started to think about the cables running down my wall from my router, which were in a 3D printed chain. I took ChArlie's design and increased the size to accommodate...

We have a film studio and I needed to print something for the 13 cables that we have to plug in and unplug every time we use it. This will be very useful for anyone with a blackmagic ATEM Mini. I made the dimensions fit for the wires that I have, but...

It is presented in the desired format electrical extension cord black 4 in one cable and plug with 3 USB port with color lights 3D model product 3ds max was created. high quality presentation is made. Its poly structure is smooth. It has a pattern...

Just another cable holder. ... The hole for the screw/nail is 4mm Version 1 is for thick cables (230/115V etc) Version 2 is for thinner cables (audio, ethernet, ub etc.)

Ethernet CAT-6e (diameter 7mm) cable holder. Used to organize bunch of cables in server cabinet. Several holders can be placed one after another. ...Item length matches to 8-port bracket on Cisco switch.

Cable Holder for avoiding that cables fall off the table :-Done version for thin cables (like USB / Ethernet) and one for thicker cables (Display Port / DVI / HDMI...)Also, on request there is also a new version for 2 small and 1 big cable and one...