esun filament 3d models

One of the most promising spool was the one I found over at Prusa: https://www.prusaprinters.org/prints/55820-reusable-filament-spool-esun-and-inland-compatible Unfortunately the two spool models didn´t fit my Ender 3 build plate :-( Trying to print...

To see more projects like this one follow : https://www.instagram.com/Concretize_3d/ This support was designed to facilitate the passage of the filament when using the eSUN eBOX, as it has a fitting for the hose, but even if you do not have an eBOX,...

The side bumpers and the rear power plug make it impossible to fall when the filament gets stuck. ... This is a remix of https://www.thingiverse.com/thing:4075759 that removes the necessity of the assembly of the fixation screw containing a metal...

I designed this to allow using silica gel spheres on esun e-box filament dryer. All other designs available up to now work with silica bags. This silica tray don't have a lid, so be careful, do not tilt down the e-box. The actual print size...

... After installing inks007's original design and experiencing the issue where the shafts fell out of the bearings within about 10 minutes, resulting in a spool collapse to one side and my filament snapping, I decided to redesign this base.

One of the most promising spool was the one I found over at Prusa: https://www.prusaprinters.org/prints/55820-reusable-filament-spool-esun-and-inland-compatible Unfortunately the two spool models didn´t fit my Ender 3 build plate :-( Trying to print...

This makes 5mm range ditch and causes so terrible dropout filament issue during printing, in worst case you need to waste full of filament bunch!BUT to make full printing spool makes no sense. It just wasts 100-300g of filament with not so short...

Refill compatibility: NO: eSun (different hub OD) NO: Solutech (different hub OD) YES: Push Plastic 500g (use two-part adapter) Files... eSun2Push5.stl - 1kg adapter eSun2PushHalf-ShortCore.stl - 0.5kg refill core adapter eSun2PushHalf-Flange.stl -...

The esun spools are overwound from the supplier so require a fit with less than a 1mm gap to prevent the filament from despooling off and tangling. Also, I redesigned the lovely Spannerhands design because my spools are kept inside an autoclave...

eSun Masterspool for eSun Respool refills Money and time saving design 2 piece no core fast print. ... Thank you for visiting our page -Rogue Paul ;)

This converter lets you repurpose the 3D Solutech cartridge holder for eSun recharging units.

... Expand the feet of the stand, and make it really tight when assembling. 2. Make a hole on the body part , saving more filament and allowing the air to circulate.(maybe :P) Hope you like it !! P.S. ...it's rainy day ,so the humidity is terrible...

It allows use of 1 kg InLand / eSUN filament and any roll of similar diameter with width less than 66 mm and greater than ~ 60 mm. This design requires four 608 size skateboard bearings. EDIT: This no longer works with Microcenter filament. ...The...

The default settings should fit most eSun filament spools. Default settings on this customizer are for: Filament Spool Brand:eSun Bearing Size:5mm Center Bolt Size:M5 Brim Size:2mm Print Settings Printer Brand: RepRap Printer: RepRap Kossel Rafts:...

Use eSUN PLA+ if you want pretty chain links; I've tried most highly-rated filaments and eSUN is by far the best. Avoid using standard PLA (brittle) or PETG (bad action). Use the Cura settings for all Ender models, ignore G-code info. Visit...

Aside from the awful PTFE tube grommet, the big issue is that the roller mechanism is too narrow for many 1kg filament spools, making it unusable with certain types of filament like Rigid Ink. I realized that the stock rod and bearings in the V2...

I've added cutouts for buttons.Printing time for both parts is 12 hours.EDIT: After several days of use, I noticed that I made too large an angle between the dryer base and the vertical (it was 120% as in the original), therefore the filament spool...

Due to overwinding by the supplier, these spools require a gap of less than 1mm to prevent filament from unwinding and becoming tangled. I've also revamped the Spannerhands design because my spools are stored inside an autoclave with the printer,...

Resin bottle cap for Inland/esun/Yousu metal bottles. Printing this as a test to figure out the correct thread pitch. ... **Use the v9 stl file

Resin bottle cap for Inland/esun/Yousu metal bottles. ... Printing this as a test to figure out the correct thread pitch.

I've been following the progress of the #masterspool initiative on twitter and realised I could repurpose an eSun 1kg spool for this purpose.

This is designed exclusively for ESUN filament where spools are more compact, both for the lighter 0.5kg and heavier 1kg varieties. It reduces the overall footprint of the printer. The original nuts fit seamlessly when used. It accommodates spools...

Since boxes like eSUN filament boxes cost nearly a hundred bucks, just to keep one single filament roll dry and tempered, I designed my own. To make it work, you'll need these add-ons: A hygrometer/thermometer (I used this one:...

(it's cheap!!)I make some changes base on the original design.Expand the feet of the stand, and make it really tight when assembling.Make a hole on the body part , saving more filament and allowing the air to circulate.(maybe :P)Hope you like it...

Trophy made for the #esuntrophydesign "eSUN Trophy Design Contest" https://www.facebook.com/events/912722686543584 Tools used https://www.visioncortex.org/vtracer/ ( to get a .svg from an image ) https://inkscape.org/ ( to edit .svg files )...

Spun Text: eSUN 52mm spool adapts to a 20mm axle seamlessly. ... A customized version of the original design found at Thingiverse, with ID number 735213, was created using the Customizer app.

Print two instances of the Little Master Spool Roller V2.0, specifically the 200mm part one, along with a custom-designed middle section. ...These components are designed to be securely attached using screws sourced from repurposed eSun spools.

I'm keeping tabs on the #masterspool initiative on Twitter, and it's got me thinking - what if I could repurpose an eSun 1kg spool to take this project to the next level?

This adapter allows you to reuse the 3D Solutech spool thing for eSun refills. ...The dimensions are 75.19 mm inside diameter and 90 mm outside diameter.</p> Category: 3D Printers

Customized version of https://www.thingiverse.com/thing:4776109 Suits eSun 3kg spools supported by a 25mm tube. Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4776109