esun filament 3d models

I wanted it to print as fast as possible and use as little filament as I think I could use without loosing too much strength. So far, its holding up well. Simple to print, just lay flat on bed. Uses countersunk M5x25-30mm X 2 to hold itself...

Print Settings Printer: Fabrikator Mini V1.5 Rafts: Turned Off Supports: Disabled Resolution: 0.2mm High Precision Infill: 15% Moderate Density Notes: I Am Printing With Repetier Host And Cura Slicer, Using PLA Filament. In The Print Settings, Make...

I've added the Hygrometer from the Sunlu version to Esun version with Orca Slicer

Simple but effective master spool for eSUN PLA refilament spooless filament.I noticed that some of my other master spools did not fit the eSUN brand so I made this one.You will need:QTY:3 M5x60mm SHCSQTY:3 M5 NutsCompatible with my Creality Smooth...

This is a small cap for eSUN USB pump, to protect the sealing ring at the bottom of the pump from dust.

This is a simple filament color card. After removing the label on Esun brand filaments, you can paste it on the color card. Note: It is possible to heat the label with a lighter and then remove it without deforming.

... color chart. ...Simply strip away the sticker from an Esun brand filament and stick it onto this color guide. ...Note: It's actually quite easy to melt off the label using a flame from a lighter, allowing you to remove it without causing any damage.

Since boxes like eSUN filament boxes cost nearly $100, just to keep a single roll of filament dry and tempered, I designed my own DIY solution. To make it work, you'll need these essential add-ons: A hygrometer/thermometer (I used this one from eBay)...

Fiberlogy refills have different dimensions so it would slack and tangle itself on esun spools. I made this "adapter" to fit fiberlogy refills to esuns spool. Print 2 of it. One stl made to print without top and bottom layers te make infill structure...

As esun sells the vacuum pump without a stand, i have constructed a simple stand. ...The silicone seal is also not stressed and protected by the stand when mounted.

This version of the eSUN centring disk holds the spool firmly by mating up with the recessed 53mm hole. ...Modelled on the original 50mm centring disc, I created a new f3d model to make the re-design easier.

Reuse your ESUN Spools with this print. Just saw a flange off from the inner edge of the barrel. ...The arbor fits the Ender 3 v2's spool holder.

Base que sustituye a los rodillos de serie, para poner la secadora de filamento eSun Ebox. En mi caso tuve que partir la base en dos ya que no entra en la cama. Dispone de un acople para poner el sensor de filamento. ... Use soportes para el...

The other two eSun Repwinder spacers I found on Printables did not fit my masterspool, so I created my own.This model is parametric, so it can be customized for any spool you have. ...It features notches/tabs to lock into the Prusament spool ring and...

During long printing, the coil shifts in the dryer marks eSUN to the right. To avoid this problem I made a centering guide, the coil stays well in the center throughout the printing. ... Just center the guide in the hole of the coil and make a small...

Reuse the new eSun black reels using this hub. To start cut an empty reel about 1/2inch (12mm) from one side. Use the large hub to align the 2 halves and the smaller hub to the other side. Use 2 x 3mm screws to hold the 2 hubs and reel...

Course temperature calibration for eSUN PLA+(205-225 degrees) is essential to achieve optimal prints. A customized version of the original calibration guide can be found at Thingiverse, specifically in the thing: 915435. ...This customizer app was used...

... suspect it would benefit from being printed at a higher level of detail. You might also consider printing a cylinder spacer to keep the bearing in place exactly where you want it - I ended up printing two spacers to match the width of my ESun spool.

As there doesn't appear to be any spool holders using bearings in this formfactor which fits 5kg eSun branded rolls, I decided to modify a design and add my own touches to make it easy to switch rolls over with just two pieces. Print: 1 x frame ...

Hello everyone, I'm excited to share with you a custom design I've created for use with eSun spool technology. This innovative part was designed to seamlessly integrate onto the spool itself, and its clever integration with a 608ZZ bearing allows for...

Like many people, I have a love/hate relationship with my eSun eBox. It has some nice features, but I've already had to take it apart and re-solder one connection- and it just did not play well with some of the smaller-diameter spools that I've got.

This is a spool holder specifically designed for 3D Systems' CubePro 3D Printers, perfect for users who frequently employ Esun filament, such as PLA+, without any issues. ...For enhanced performance and reliability, I highly recommend pairing this spool...

Just a simple design of a eSun and Sunlu filament dryer box holder for the qidi xmax.

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:4946514 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4946514

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Removing the 3D printing spool's components is a breeze, thanks to its clever design. The spool comes with two easy-to-remove parts - the disc and pressure plate. ...With a simple twist, you can swiftly unload and reload your consumables without any...

I created a 7-inch-long model that can be easily scaled up or down. To assemble it, I applied super glue to the individual letters, carefully attaching them one by one. ...Enjoy my latest creation, Bretware!