esp32 housing 3d models

This is a mount for this housing for the ESP32: https://www.thingiverse.com/thing:3195951 As I use ESP32s to detect room presence in my home I needed a way to mount the board in it's housing. ...So I desiged a slide-in-style mount that allows me to do...

A simple housing for an ESP32 controller, comes with 2 flavors with the diffrence being one has a "tunnel" open up to the lid and one only has a hole for the cables to run through.

ESP32 cam housing

A House Case for ESP32. ...It has 2 chambers: 1 for the esp32 and 1 for all external sensors so they get access to air

[3D Printed Modular Holder System: esp32-cam housing](https://www.mischianti.org/2021/09/15/3d-printed-modular-holder-system-esp32-cam-housing-2/) You can find all the modular bracket/arm support knobs for this housing here. ... [3D Printed Modular...

This is a housing I designed for the esp32 port of the squeezelite LMS player. Here is the github of the project: https://github.com/sle118/squeezelite-esp32 I designed it for the ttgo t7 v1.4 esp32 module, 5 buttons (10 mm height), a rotary encoder...

The project requires a housing for the electronic components, so I've created a box to fit everything together securely. ...To ensure reliable connections, I've also included a connector holder that keeps the PCB in place and prevents accidental...

I designed this as housing for a project to communicate with solar inverter and utility power measuring device. Out of the box this board has everything to be a gateway from Canbus and/or rs485 to the network. I use its rs485 interface with...

Housing for an ESP32-cam, with or without antenna.

Housing for the ESP32 Cam Module Compatible with Tinker Board

Housing for an ESP32-cam, with or without antenna.

Housing for ESP32 Cam modul (Tinker board) Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0,2 Infill: 100% Notes: After printing you can use female breadboard connectors with the plastic removed, and put...

The current design isn't finalized yet - specifically, it doesn't support mounting the PCB to the housing or adding a suitable USB connector hole. Additionally, the battery connector and reset button have not been designed as of now. ...As I mentioned...

Required components besides the two printed parts: wrover esp32-cam module two nuts M5 four screws, 60° head, M3x16 (screwed directly into the plastic) For best firmware I found for this module, please refer to this GitHub repository:...

Required Components: - Wrover ESP32-CAM module - Two nuts M5 - Four screws with 60° heads, M3x16 (directly screwed into plastic) For optimal firmware performance on this module, refer to the GitHub repository at...

I really liked the ESP32 camera mount design by Electronlibre but it needed some changes to fit the 160 cam that I'm using so I remixed it. I also made an extention so I could be more flexible with my plasement of the camera. Want to tip me...

I've added round holes for more heat dissipation. ...The ESP32-CAM gets very hot and the original files had a mesh way of creating holes. ...These holes are much larger and will allow the camera to cool down even more.

Changes to origional: - removed the thread for a lens - added grooves for the buttons that are on my shield - removed the mount - added remove-able lid - added housing with mounting points outside of the housing It is a pain to get the antenna into...

The provided STL file does not include the bricks I added to accommodate the floppy drive; instead, a FreeCAD file is included where you can customize your housing by adjusting several parameters in a spreadsheet. Don't forget to add space for...

The original [ESP32 Cam housing](https://www.thingiverse.com/thing:4192843) design was very simple and compact. So, starting with that design, I added - Top: Micro-SD/TF card slot - Top: External antenna - Bottom: Access to reset button -...

I designed a housing including a mount which is closed thightly with just one M4X50 Screw and a nut. The flash and SD Card is usable. The design with exAnt ist for use with an external SMA antenna like it's often sold in sets with the ESP32-CAM. ...

... surveillance environment ist MotionEyes (on Raspberry Pi 3). Firmware and further instructions for RTSP-Streamer ESP-32 Cam can be found on https://bitsnblobs.com/rtsp-video-streamer---esp32/ https://github.com/bnbe-club/rtsp-video-streamer-diy-14

I needed CO2 sensors in various rooms around the house, so I came up with a custom housing for the ESP32 that includes pods for both the DHT22 temperature/humidity and MH-Z19 CO2 sensors. I flashed the ESP32 with EasyESP software and connected the...

This is a housing unit for an MQ series sensor & esp32 combo unit, snap fit.

Housing for ESP32-CAM with jimbal joint for wall mountic. The housing is provided also with slot for sealing cord dia. ...2.5mm and slot for RJ 12 female conector.

A simple housing with a swivel mount for the esp32 cam. The lid is just snaped on, no screws needed. ... The hole in the side of the housing is meant to be used for an extern antenna.

Housing for ESP32-CAM with jimbal joint for wall mountic. The housing is provided also with slot for sealing cord dia. ...2.5mm and slot for RJ 12 female conector.

I built a custom housing for my ESP32 webradio project that consists of three distinct components, each printable with minimal or no support required. Print the front and rear plates face down, while printing the main body on its end. ... Check out...

This housing is designed for the ESP32-CAM including ESP32CAM-MB und an optional external Antenna. I just use them for the Prusa Connect integration.While I wanted to make the housing as small as possible I kept the hole for the Micro-USB connector...

I remixed the top of the housing as I found that the board I had was a little bit taller, looks like the exact height of the plastic of the black strip connector. I also added a hole for the illumination LED. ...The original model is very nice and the...