esp32 d1 mini 3d models

I needed a Wemos D1 Mini case that had room for some passive electrionics and an extended power harness for WS2812B LED Strips. ...Loaded the original Fusion 360 design file by Surrbradl08, modified the sketch to extend the length of the case, and...

Also added a 3.5mm jack connector hole which can be used for audio out.Designed to house the Wemos D1 Mini to use with the customer firmware https://github.com/ramapcsx2/gbs-controlCut-outs for all the connectors including micro USB for the D1 Mini...

:)Demo of print status screens: https://imgur.com/a/yX2dhjJCompact Case for Wemos D1 mini wifi ESP8266 with 0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display.Uses (1) 10mm M3 screw for assembly.Used this wire - great for projects!I used...

... comments and I'll try and add more. Items needed: 400 point tie-point breadboard NodeMCU or D1 mini board.. ...(pin-header should be inverted so it might be easier to order one that is not pre-soldered) Little screws (or you can hot glue)

I designed my own case for the 16bit LED ringlight controlled by a Wemos D1 mini. I added also the possibility to insert a pushbutton for on/off or change color and three holes for an IR receiver. The input voltage is 5 Volt and the consumtion is...

... in the comments and I'll try and add more. Items needed: 400 point tie-point breadboard NodeMCU or D1 mini board.. ...(pin-header should be inverted so it might be easier to order one that is not pre-soldered) Little screws (or you can hot glue)

Reading a G4 RF1 gas meter with TCRT5000 sensor and WeMos D1 Mini. ... Fits perfectly for a G4 RF1 gas meter Please refer: https://be-jo.net/2022/02/home-assistant-gaszaehler-mit-esphome-auslesen-flashen-unter-wsl/ ...

Here is a box suitable for an "ESP32-C3 mini" controller and a stepper motor driverThe controller in itself is very small, and has been welded to the driver control pins through its pin 1+2+3+4 (supporting the I/O port of the same name)Such...

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Customized version of https://www.thingiverse.com/thing:1776349 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1776349

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Inspired by the innovative project from Alex Gyver: https://www.youtube.com/watch?v=771-Okf0dYs&feature=emb_logo. This lamp is specifically designed to work with a 1m LED strip featuring 60 diodes. To assemble the lamp, you will need 10 segments...

Customized version of https://www.thingiverse.com/thing:3415783 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3415783

This is a remix of my 8x8 Pixel Matrix design. There are cutted versions for all the parts in case the full parts wouldnt fit your 3d printer. For more details check out this design: https://www.thingiverse.com/thing:4776182 This design is made...

A little remix : Wemos and screen dimensions adjustement, design, accessible reset button. ... See the original for software instructions: https://www.thingiverse.com/thing:2884823 or the GitHub page: https://github.com/Qrome/printer-monitor

Customized version of https://www.thingiverse.com/thing:3415783Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3415783

I'm building a compact enclosure to house an ESP8266 board and two sensors. ...This DIY project aims to enhance Home Assistant's ability to manage my household more effectively!

Customized version of https://www.thingiverse.com/thing:3194520 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3194520

Customized version of https://www.thingiverse.com/thing:1776349 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1776349

I liked the design from https://www.thingiverse.com/thing:3550295 very much but I didn't need the hole for the switch so I removed it.

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

customized with 3D Slash!

Printing immediately, no testing required. Very tight tolerances are in effect. Printing triggers an automatic update to the design parameters. If a critical error occurs during printing, adjust the tolerance settings as needed. A reset button is...

Customized version of https://www.thingiverse.com/thing:3415783 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3415783