esp32 cam home assistant 3d models

Compact enclosure for the ubiquitous ESP32-CAM with the USB-Serial board and an external antenna. The program- and reset-button are still accessible through the cooling slits. Update: SD-Card also accesible now! The holes in the bottom piece...

Required Components: - Wrover ESP32-CAM module - Two nuts M5 - Four screws with 60° heads, M3x16 (directly screwed into plastic) For optimal firmware performance on this module, refer to the GitHub repository at...

This housing is intended for outdoor use of the ESP32-Cam microcontroller. There are fixtures for 5mm LEDs. I use infrared LEDs, so the camera can be used in the dark without visible light. But this requires a small modification of the ESP32 cam...

This is a customized version of some esp32 cam boxes that I found because the module I got seemed not to be the size of others as well as a different position of the led (or the other designs are wrong in size). I wanted to make a version as compact...

Things Needed: Ai-thinker ESP32 cam 16 Led Neopixel Ring M3 Screws (5mm) M3 threaded inserts OD- 4mm (Optional) 3.5mm DC male/ female connector 5V Power Supply (Can use buck converter to lower the voltage of printer power supply from 24v to 5v)...

The download is only intended for private and personal printing.Here you can find my special Code adaption to use the flash LED while streaming to monitor my printer while printing in the dark: uniforx/esp32camX: This is my adaption of the default...

Using this clamp you can mount the camera module on a ESP32-Cam board in two orientations. For 90° rotation carefully fold the flex-print cable as shown and put some foam below the camera module, then snap the clamp on. Print Settings Printer Brand:...

I like the simplicity of Carsten's ESP32 Cam Clamp and how it holds the camera in place. However, I wanted it to fully cover the front and use it with a <a href="https://www.aliexpress.com/item/1005003279204315.html">120 degree wide-angle lens</a>,...

This is design to work with a MG90S servo motor and the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Demo: https://youtu.be/v_A3rCVCbVE Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No...

This is design to work with a the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: PolyMaker...

I've made this box for wallmount for a combined esp32 cam (blank camera is also shown on the picture). Not sure if all of these sold are within the same measurement, so I uploaded the fusion360 file. All parts/bodies are seperated by 0.1mm in this...

... from ebay. esp32-cam AI thinker 2n2222 npn with a 1k resistor for amplifications of the PWM I found on youtube. The printed one on picture with the circuit is a first version. ... https://github.com/moxl-420/ESP32cam-doorbell For full info

This housing is intended for outdoor use of the ESP32-Cam microcontroller. There are fixtures for 5mm LEDs. I use infrared LEDs, so the camera can be used in the dark without visible light. But this requires a small modification of the ESP32 cam...

// esp32cam-enc.scad // // A pan/tilt mounting box for esp32-cam crafted in openscad for // a very cool wireless esp32 video/still camera board that only costs around $5. // // The enclosure can be printed for about $0.60 in filament. // // The...

The project uses only an ESP32-CAM as the entire motion detector and the microcontroller driving the stepper motors. The entire project is open source allowing you to use this in robotics or other projects where you need a cheap and easy motion...

The project uses only an ESP32-CAM as the entire motion detector and the microcontroller driving the stepper motors. The entire project is open source allowing you to use this in robotics or other projects where you need a cheap and easy motion...

The project uses only an ESP32-CAM as the entire motion detector and the microcontroller driving the stepper motors. The entire project is open source allowing you to use this in robotics or other projects where you need a cheap and easy motion...

I saw a few tools for adjusting the focus on various Raspberry Pi cameras, but they were all wrong for my use case, which was an ESP32-CAM, so I started designing my own from scratch in a learn-as-you-go kind of way. BTW, this Thing started me...

I've created a DIY ESP32 Camera Mount. ... Remade from: ardenpm - https://www.thingiverse.com/thing:3708345 Reimagined with: CreativeTools - https://www.thingaverse.com/thing:1017689

Simple enclosure for ESP32 CAMPrinted in PLA; 04mm nozzle; 0.16mm layer height: 28min print time for each halve with a Creality Ender-2

The Micro USB camera module is a cutting-edge addition to the popular ESP32 development board, enabling users to easily capture high-quality images and videos.

A very compact case for an ESP32 CAM Module. Some things to note, I initially designed this for my own use and I'm just sharing in case anyone else wanted to utilize the design. With that said, there's a few proprietary features to this design. I...

A very compact case for an ESP32 CAM Module. Some things to note, I initially designed this for my own use and I'm just sharing in case anyone else wanted to utilize the design. With that said, there's a few proprietary features to this design. I...

A housing unit designed specifically to accommodate the ESP-32 CAM module.

A case for a ESP32_camm with space for a 18650LiPo-cell and a TP4056 MicroUSB charger module. ... I drilled the hole for the switch after printing, so it is not in the model and are optional.

By utilizing the ESP32 microcontroller, the smart home sensor can provide users with an efficient and reliable solution for home automation and security. The combination of the mmWave radar, PIR, and temperature sensors, along with the processing...

arduino code here: https://github.com/devinzhang91/esp32_timelapse YOU need: esp32cam USB-typeA Screw & Nut ： M5*30 You can also buy battery bank like : one 18650 with diameter is 22mm Tripod is come from: https://www.thingiverse.com/thing:1165406...

This is a remix of https://www.thingiverse.com/thing:4192096 I print out the box is on it and my esp32 didn't fit with the camera hole. I use the base of the box and the Arm. ... Lit fits tight and snap-on it very well

This is a remix of https://www.thingiverse.com/thing:4192096 I print out the box is on it and my esp32 didn't fit with the camera hole. I use the base of the box and the Arm. ... Lit fits tight and snap-on it very well

Here is a rewritten version of the text: I'm reaching out about a custom case designed specifically for the ESP32-Camera, featuring a unique pivot joint stand that offers unparalleled flexibility. ...If you're interested in learning more, please don't...