esp32 cam case battery 3d models
307637 3d models found related to esp32 cam case battery.
thingiverse
... fan. The case also features a small hole for the led light of the esp32-cam. The stand is a remix of https://www.thingiverse.com/thing:4107609 thank to @MagnusT. ... Added a new case and stand with holes for screws (I use nylon screws and nuts)
thingiverse
This is a case for the Freenove ESP32-S3-WROOM CAM Board. Pretty snug fit, so you need to get your printer's tolerances in order. BOM: 4x M2 threaded insert 4x M2x8mm No support's required. ...Print using 4mm Nozzle and <=.24mm layer height
thingiverse
Minor modification of the ESP32-CAM with tripod, added some vents on top when I noticed the original case became warm, added an SD slot hole, and a reset button hole.... ...also made the flash hole a bit wider as I noticed it was a bit off to the left.
prusaprinters
Case and cover to fit ESP-32-CAM-CH340 a.k.a ESP-32-CAM Integrated. ...Remixed from "Case with kodak thread for ESP32CAM + CH340" to suit "Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2". Category: Electronics
thingiverse
This is a case for the ESP32-CAM module. It has been remixed from [the case](https://www.thingiverse.com/thing:4571627) that is intended to plug onto the various [AI-on-the-Edge](https://github.com/jomjol/AI-on-the-edge-device) contraptions. I had...
thingiverse
Well i needed a simple case with slots for both the micro SD card and the LED lamp for the ESP32-CAM module. It does not fit the USB programmer. But it has enough room for Dupont connectors to supply it with power. Clearance is tight so your...
prusaprinters
Added cooling slots in the front and rear parts of JPGuitar's mount for the ESP32-Cam. I also slightly increased the size of the cutout for the hex nut for a better fit. The 3mf contains gabr42's improved x-axis base, so all parts needed to mount the...
thingiverse
Housing crafted specifically for ESP32-cam modules, featuring precision-cut holes to accommodate 5 mm infrared LEDs in sets of three.\r\nA dedicated LED compartment securely holds the LEDs and resistor within its confines, while a partition separates...
grabcad
The mounting block itself should be screwed to the back cover of the case using a 2.5mm screw and double-sided mounting tape, or just glue it together.The case leaves clearance for the connector pins, and the mounting block leaves just enough...
thingiverse
I modified the Original Parts to Fit with the ESP32-CAM-MB Board as Programming and Power Supply. ... Right now i am still working on it.
thingiverse
This is a upgrade from https://www.printables.com/model/296079-esp32-cam-wrover-board-case
thingiverse
This is an adapter to hold ESP32-CAM in fake cheap waterproof camera case.
thingiverse
Case with common action camera mounting tabs for ESP32-Cam board. ...Use two tiny screws to close the case.
grabcad
3D model ESP32-Cam Programmerfor uploading code to ESP32-Cam with easy.https://github.com/geraicerdas/ESP32-Cam-Programmer
grabcad
3D model ESP32-Cam Programmerfor uploading code to ESP32-Cam with easy.https://github.com/geraicerdas/ESP32-Cam-Programmer
thingiverse
ESP32-CAM BOX and HOLDER Light weight and simple box for esp32-cam
thingiverse
Inspired by the design, from Pico78 for the ESP32 camm, which is still in the status "in work", I have revised the design.
prusaprinters
this is a ESP32 Cam mockup for further 3D constructions.it was not designed to be printed!I used it to construct cases like this
thingiverse
This is design to work with a the ESP32-Cam case designed by SolarGermany https://www.thingiverse.com/thing:3949787/makes